VONROC PH513AC Traducción De Las Instrucciones Originales página 10

EN
Switching on/off and adjusting the power level
(Fig. A)
The heater can be turned on and off using the on/
off switch (3). The heater is equipped with two
switches, to not only turn the device on or off,
but also adjust the power level in a total of three
different settings:
• Left on/off switch (10) turned on (I), right on/off
switch (11) turned off (O): Level 1 - 800W
• Left on/off switch (10) turned off (O), right on/
off switch (11) turned on (I): Level 2 - 1200W
• Left on/off switch (10) turned on (I), right on/off
switch (11) turned on (I): Level 3 - 2000W
Tip­over safety switch (Fig. A)
This heater is fitted with a tip-over safety switch.
In the event that the heater falls over, the heater
automatically shuts off.
Please note that when the heater is returned to its
upright position, it does not resume its operating
immediately. First switch it off (read 'switching on/
off'), remove the plug from the socket and check
the heater for damage. In case of damage or mal-
functioning do not use but offer for checking / re-
pair. If there is nog damage, you can simply switch
the heater on again (read 'switching on/off').
5. MAINTENANCE
Always make sure that the machine is not
connected to the mains electricity when you
carry out any maintenance of the mechanism.
CAUTION: Risk of Electric Shock. DO NOT
open or try to repair the heater yourself.
Clean the machine casings regularly with a soft cloth,
preferably after each use. Make sure that the ven-
tilation openings are free of dust and dirt. Remove
very persistent dirt using a soft cloth moistened with
soapsuds. Do not use any solvents such as gasoline,
alcohol, ammonia, etc. Chemicals such as these will
damage the synthetic components.
• DO NOT use alcohol, gasoline, abrasive pow-
ders, furniture polish or rough brushes to clean
the heater. This may cause damage or deterio-
ration to the surface of the heater.
• DO NOT immerse the heater in water.
10
• Wait until the heater is completely dry before
use.
ATTENTION:
• Always disconnect the heater from the electric-
ity supply and allow it to cool before attempting
to clean it.
• If the heater has collected dust or dirt inside
the unit or around the heating element, have to
unit cleaned by a qualified service agent. Do not
operate the heater in this condition.
• The only maintenance required is cleaning of
the external surfaces of the heater.
• Do not touch the heating element with bare
fingers, as residue from your hand could affect
the life of the lamp. If it is accidentally touched,
remove the finger marks with a soft cloth mois-
tened with mentholated spirit or alcohol.
• Do not attempt to repair or adjust any electrical
or mechanical functions on this heater.
• The heater contains no user serviceable parts.
Should the product suffer damage or break-
down, it must be returned to the manufacturer
or its service agent.
• Damaged supply cords to be replaced by the
manufacturer, service agent or similarly quali-
fied person in order to avoid hazard.
Storage
Store the heater in a cool, dry location when not in
use to prevent dust and dirt build up. Use packag-
ing carton to store.
Trouble Shooting
If the heater will not operate, please check the
following before seeking repair or service:
• Check if the power cord is plugged into an
electrical outlet, if not plug in.
• Check if electricity to the main fuse is working.
• Make certain the power switches are turned on
If not, choose a setting.
ENVIRONMENT
Faulty and/or discarded electrical or
electronic apparatus have to be collected at
the appropriate recycling locations.
Only for EC countries
Do not dispose of power tools into domestic waste.
According to the European Guideline 2012/19/EC
WWW.VONROC.COM