Listening To Dab Radio - Makita DMR056 Manual De Instrucciones

● The charger may not supply power to some USB
devices.
● When not using or after charging, remove the USB
cable and close the cover.
● Do not connect this USB socket with your PC
USB port, as it is highly possible that it may cause
breakdown of the units.

LISTENING TO DAB RADIO

Tuning into DAB stations
To tune into DAB radio stations, follow these steps:
1. Turn on the radio using the Power button.
2. Select the DAB radio mode by repeatedly pressing
the Mode button.
3. If this is the first time the DAB radio mode is being
used, the radio will automatically perform a full scan
in order to find all available DAB radio stations.
During the scanning process, as new stations are
detected the station counter will increase and the
stations will be added to the list which is stored in the
radio. The bar graph indicates the progress of the
scan.
4. When scanning is completed, the radio will list all
stations that were found. Use the Tuning up or Tuning
down button to scroll through the list of stations and
press the Select button to tune into a station.
NOTE:
For DAB radio mode, if the radio's reception is not good,
it may be necessary to relocate your radio to a position
giving better reception.
The DAB radio menu
You can open the DAB radio menu by pressing and
holding the Info/Menu button while the radio is in the
DAB radio mode. Use the Tuning up or Tuning down
button to select one of the options and then press the
Select button to confirm your choice.
The radio's default and recommended settings are
indicated using an asterisk.
The DAB radio menu offers the following options:
● [Full Scan]: Select this option to perform a full scan
and store all DAB radio stations that were found in
the station list.
● [Manual tune]: Select this option to manually tune
into a DAB channel/frequency.
● [DRC]: Dynamic Range Control (also known as DRC)
can make quieter sounds easier to hear when your
radio is used in a noisy environment by reducing the
dynamic range of the audio signal.
Select this option and then use the Tuning up or
Tuning down button to highlight the required DRC
setting:
[1]: Maximum compression applied.
[1/2]: Medium compression applied.
[0]: No compression applied.
Press the Select button to confirm the setting.
● [Station order]: Select this option and
subsequently [Alphanumeric] to sort the station list
alphanumerically or select [Ensemble] to sort the
station list by DAB multiplex or select [Valid] to show
only those stations for which a signal can be found.
● [System]: Select this option to go to the system
menu settings and configure the radio (refer to the
chapter "Using the System menu" for details).
● [Back]: Select this option to go back one step in the
radio's menus or return to the previous screen.
Showing DAB information on the
display
When listening to a DAB radio broadcast, repeatedly
press the Info/Menu button to cycle through the following
information on the radio's display:
● Dynamic Label Segment (Scrolling text)
● Program type
● Multiplex name
● Frequency and channel
● Signal error/Strength
● Bit rate/Audio type
● Date
LISTENING TO FM RADIO
Tuning into FM stations
To tune into FM radio stations, follow these steps:
1. Turn on the radio using the Power button.
2. Select the FM radio mode by repeatedly pressing the
Mode button.
3. Press and hold the Tuning up or Tuning down
button to automatically tune into an FM station with
a higher or lower frequency respectively. Your radio
will stop scanning when it finds a station of sufficient
strength. The display will show the frequency of the
signal which has been found. If RDS information is
available, after a few seconds the display will show
the radio station name.
4. Press the Tuning up or Tuning down button to fine-
tune the frequency with steps of 0.05MHz if needed.
5. Repeat the steps 3 and 4 to tune into other radio
stations.
NOTE:
For FM radio mode, if the radio's reception is not good,
it may be necessary to relocate your radio to a position
giving better reception.
9 ENGLISH