Technical Data; Removing A Unit From Storage - stayer GAS CUTTER 33 Manual De Instrucciones

Ocultar thumbs Ver también para GAS CUTTER 33:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 1
Do not cut with dull, cracked or damaged
metal blade. Before cutting growth, inspect
for obstructions such as boulders, metal
stakes or strands of wire from broken fences.
If an obstruction can not be removed, mark its
location so that you can avoid it with the blade.
Rocks and metal will dull or damage a blade.
Wire can catch on the blade head and flap
around or be thrown into the air.
Do not use a brush cutter for cutting trees.
MAINTENANCE
11.
Air filter
CAUTION: NEVER operate trimmer without the air filter or
dust and dirt will be sucked into the engine and damage it.
The air filter must be kept clean. If it becomes damaged,
install a new filter.
- Accumulated dust in the air filter will reduce engine
efficiency, increase fuel consumption and allow
abrasive particles to pass into the engine. Remove
the air filter as often as necessary to maintain in a
clean condition.
- Light surface dust can readily be removed by tapping
the filter. Heavy deposits should be washed out in
soap water.
- Remove filter cover by loosening air filter cover knob.
NOTE: Replace filter if frayed, torn, damaged or
if it cannot be cleaned.
Fuel cap / fuel filter
CAUTION: Remove fuel from unit and store in approved
container before starting this procedure. Open fuel cap
slowly to release any pressure which may have formed in
fuel tank. Keep vent on fuel cap free of debris.
- Lift fuel line and filter out of tank. A steel wire with a
hook or a paper clip works well.
- Pull off fuel filter with a twisting motion.
- Replace the fuel filter.
NOTE: Never operate the tool without the fuel
filter. Internal engine damage could result and /
or disturb a good operation.
When the inside of the fuel tank is dirty, it can be cleaned
by rinsing the tank out with gasoline.
Carburettor adjustment
The carburettor was pre-set at the factory for optimum
performance.
When further adjustment is necessary, contact the service
department.
ENGLISH
28

TECHNICAL DATA

12.
= Rated power input.
= Load speed.
= displacement.
C.C
Ø
Ø
= Length trimming.
Ø
Ø
= Length cutting blade.
Ø
Ø
= Diameter of the shaft.
Ø
= Shaft length.
Ø
= Fuel tank capacity.
Ø
= Weight.
= Sound power level.
L
WA
L
= Sound pressure level.
PA
= Vibration.
NOISE
13.
Noise emission values determined according to
EN 62841-1.
Wear hearing protection.
STORAGE
14.
WARNING: Failure to follow these steps may
cause varnish to form in the carburettor and
lead to difficult starting or permanent damage
after storage.
- Clean outside surface of unit.
- Drain fuel from the fuel tank.
- After fuel is drained, start engine.
- Run engine at idle until unit stops. This will purge the
carburettor of fuel.
- Allow engine to cool (approx. 5 minutes).
- Using a sparking plug wrench, remove the sparking
plug.
- Pour 1 teaspoon of clean 2-cycle oil into the
combustion chamber. Pull starter rope slowly several
times to coat internal components. Replace sparking
plug.
- Store unit in a cool, dry place away from any source
of ignition such as an oil burner, water heater, etc.
- Put the sleeve on when not in use or in transportation.

REMOVING A UNIT FROM STORAGE

15.
- Remove sparking plug.
- Pull starter rope briskly to clear excess oil from
combustion chamber.
- Clean and gap sparking plug or install a new sparking
plug with proper gap.
- Prepare unit for operation.
28

Publicidad

Tabla de contenido

Solución de problemas

loading

Productos relacionados para stayer GAS CUTTER 33

Este manual también es adecuado para:

Gas cutter 43 b

Tabla de contenido