Tabla De Contenido; Table Of Contents; Product Specifications Kn M-3059R; Warnings - KNOVA KN M-3059R Manual Del Usuario

TABLE OF CONTENTS

Table of contents ............................................................... 1
Product specifications KN M-3059R ................................... 1
Warnings ............................................................................. 1
Symbols .............................................................................. 1
Power tool safety ................................................................ 2
Miter saw safety ................................................................. 3
Electrical requirements and safety ...................................... 4
Accessories and attachments .............................................. 5
Tools needed to remove or install blade / Tools needed for adjustment ... 5
Carton contents .................................................................. 6
Know your folding miter saw ............................................... 7

PRODUCT SPECIFICATIONS KN M-3059R

MOTOR
Power Source: 120V AC, 60Hz, 15 Amp
Speed (no load): 4,000 RPM (No load)
Electric Brake: Yes
Double insulared: Yes
Arbor shaft size: 5/8 in.
BLADE
Diameter: 12 in.
Arbor hole: 1 in.
MITER SAW
Miter Range: 0º - 50º Left, 0º - 60º Right

WARNINGS

WARNING
Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains
chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other masonry products, and
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemi-
cal: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed
to fiter out microscopic particles.

SYMBOLS

WARNING ICONS

Your power tool and its Operator's Manual may contain "WARNING ICONS" (a picture symbol intended to alert you to, and/or in-
struct you how to avoid, a potentially hazardous condition). Understanding and heeding these symbols will help you operate your tool
better a. safer. Shown below are some of the symbols you may see.
SAFETY ALERT: Precautions that involve your safety.
PROHIBITION
WEAR EYE PROTECTION: Always wear safety
goggles or safety glasses with side shields.
WEAR RESPIRATORY AND HEARING PROTEC-
TION: Always wear respiratory and hearing protection.
READ AND UNDERTAND
reduce the risk of injury, user and all bystanders must
read understand
product.
MITER SAW
Miter Detent Stops: 0, 15, 22.5, 31.6, 45º R & L
Bevel Range:
Bevel Positive Stops: 0°- 45° Left
CUTTING CAPACITY
Crosscut:
Miter 45° R & L: 2-1/2 in. x 5-1/2 in. / 3-7/8 in. x 4-1/8 in.
Bevel 45º L:
45° Miter and 45° Bevel: 1-3/4 in. x 5-1/2 in. / 2-1/2 in. x 4-1/8 in.
Crow molding nested: 6-5/8 in.
Base molding against fence: 4-5/8 in.
OPERATOR'S MANUAL
before using this
Operator's Manual
Glossary of terms ..............................................................
Assembly ...........................................................................
Adjustments ..................................................................... 12
Operation ........................................................................... 17
Crown molding chart .......................................................... 23
Maintenance ...................................................................... 24
Troubleshooting guide ....................................................... 25
Parts list ............................................................................ 26
Machine schematic ............................................................ 28
Parts list and motor schematic .......................................... 29
Notes ................................................................................. 60
and 60º Right
0°- 48° Left
2-1/2 in. x 7-7/8 in. / 3-7/8 in. x 5-7/8 in.
1-3/4 in. x 7-7/8 in. / 2-1/2 in. x 5-7/8 in.
KEEP HANDS AWAY FROM BLADE: Failure to keep
your hands away from the blade will result in serious
personal injury.
SUPPORT AND CLAMP WORK
DANGER: Indicates an imminently hazardous
DANGER
situation which, if not avoided, will result in death or
serious injury.
WARNING: Indicates a potentially hazardous
WARNING
situation which, if not avoided, could result in dead or
serious injury.
CAUTION: Indicates a potentially hazardous
CAUTION
situation which, if not avoided, may result in minor or
moderate injury.
: To
CAUTION: Used without the safety alert symbol indi-
CAUTION
cates a potentially hazardous situation which, if not avoided,
may result in property damage.
1
WARNING
To avoid electrical
hazards, fire hazards or damage to
the tool, use proper circuit protection. This
tool is wired at the factory for 110-120 Volt
operation. It must be connected to a 110-
120 Volt / 15 Ampere time delay fuse or
circuit breaker. To avoid shock or fire, re-
place power cord immediately if it is worn,
cut or damaged in any way.
Before using your tool, it is critical that you
read and understand these safety rules.
Failure to follow these rules could result in
serious injury to you or damage to the tool.
8
8