Tuning Operations; Depth Adjustment; Cutting Direction; Repair Service - stayer PR10E Manual De Instrucciones

4.2.Tuning operations

VARIABLE SPEED (PR10E)
Located on the handle there is the variable speed button
. To increase or reduce the speed, it is only necessary to
rotate the knob. The smaller the cutter is, the higher is the
speed and viceversa. Acutter rotating to fast or advancing
to slowly may burn the work piece entailing the hazard of
fire.

DEPTH ADJUSTMENT

This machine is equipped with a depth stop and a depth
scale allowing a quick selection of the depth.
The magnifier at the register line can also be slid upwards
or downwards to facilitate adjustment and lecture of the
depth scale.
The depth stop and the scale can be moved upwards
and downwards by rotating the knurled adjustment screw
clockwise or counterclockwise to set the position of the
cutter regarding the work piece or the required cutting
depth, relative to the depth scale by using the locking
button to lock the distance.
FINE ADJUSTMENT (PR10E).
When the approximate depth has been set and locked,
a finer adjustment may be carried out by using micro
adjustment knob. An additional adjustment (depth of
penetration) may be achieved by means of the knurled
screw at the bottom of the depth scale, stop.
4.3 General instructions for use
In accordance with the different applications, there is a
great variety of milling cutters of very different realizations
and qualities.
High yield quick cutting steel milling cutters are suitable
to work on soft materials as for example soft wood and
plastic.
Milling cutters with hard metal blades are especially
suitable to work on hard and abrasive materials as for
example hard wood and aluminum.
WARNING: use clean milling cutters and in a perfect
condition.
CUTTING IN MULTIPLE RUNS (PR10E)
This machine is equipped with a turret mechanism
establishing the maximum cutting depth by means of
seven stages. Each step of the turret is approximately to 3
mm cutting depth. Adjust the desired depth with the turret
depth scale starting from its minimum stop.
This depth is set in a maximum of seven steps. Rotate
the turret so that the highest configuration is aligned with
the depth stop screw and complete the first step. Rotate
the turret to beside the most suitable cutting depth and
complete the following step. Repeat this procedure until
the required depth has been achieved.
USING THE PARALLEL GUIDE (PR10E/PR6)
Parallel guide may be used to make a cut at a distance
that is parallel to the edge of the work piece.
Slide the parallel guide to the desired cutting distance.
ENGLISH
20
By positioning the guide bars at the bottom of the cutter,
and secure with the fixing knob.
To carry out the operation, firmly hold the stop of the
parallel guide at the edge of the work piece.
USE OF THE GUIDE PLATFORM (PR10E)
The guide platform "L" is used for making a pre-cut or a
cut using a template; place the template "L" with its central
bushing protruding from its bottom. Latch the template by
pulling locker.
The guide platform is ready to continue to reproduce the
profile silhouette template.
1. Place the machine backwards as indicated in fig.13,
remove the screws.
2. Insert platform at the base of the machine and secure
the screws.
TEMPLATE SIZE
The size of the template will be determined by the size of
the cutter to be used.

CUTTING DIRECTION

To avoid vibrations in the cutter and to obtain a better
result, cuts must be made counterclockwise at the time of
outer cuts and clockwise at the time of inner cuts.
5. Maintenance and service instructions
1. Always disconnect the tool before carrying out any
inspection or cleaning. Never use water or other liquids
to clean the tool. Clean the tool with a cloth or brush.
2. Replace used, worn-out cutters.
3. The tool's cooling vents must be cleaned from time to
time to avoid excessive heating-up of the motor.
4. Always check that the components of the tool are
mounted solidly.
5. The casing must always be without any indication of
cracks or any other damages.
6. Always check that the cable is in a perfect condition.

5.1 Repair service

The technical service will provide you advice regarding
questions you may have on the repair and maintenance
of your product as well as on spare parts.
You may also obtain exploded views and information on
spare parts on the internet under:
info@grupostayer.com
20