Ilustrated Description; Placement And Testing - stayer PR10E Manual De Instrucciones

All the cutters must be fitted in the guiding platform slot,
whose diameter limits that of the cutter to use.
When using the cutter on delicate surfaces as
decorations or finishes,
decorative surfaces or those of the cutter base well
with adhesive tape or another
protection means.
STRAIGHT GUIDE
The straight guide is useful for making straight cuts when
making bevels or grooves (PR10E/PR6).
Place the guide for straight cuts onto the guide fastener
with the fastening screw. Insert the fastener of the guide
into the openings of the base of the tool and tighten the
fastening wing nut..
By using the convenient holes of the guide to screw
extra wooden pieces, one may make a straight
guide that is wider, of desired dimensions (PR10E).
When using a milling cutter having a large diameter, place
wooden pieces having a thickness of more than 15 mm
on the straight guide, to avoid the milling cutter striking
the straight guide.
When cutting, move the tool with the straight guide at level
with the side of the work piece.
If the distance between the side of the work piece and the
cutting position is too wide for the guide for straight cuts,
or if the side of the work piece is not straight, the guide
for straight cuts may not be used. In this case, fasten the
straight board to the work piece with the clamp, and use it
as a guide against the base of the router. Feed the tool in
direction of the arrow.
Trimmer guide (PR6)
Trimming, curved cuts in veneers for furniture and the
like can be done easily with the trimmer guide. The guide
roller rides the curve and assures a fine cut. (Fig. 14)
Install the trimmer guide on the tool base with the clamp
screw (A). Loosen the clamp screw (B) and adjust the
distance between the bit and the trimmer guide by turning
the adjusting screw (1 mm per turn). At the desired
distance, tighten the clamp screw (B) to secure the
trimmer guide in place. (Fig. 15)
When cutting, move the tool with the guide roller riding the
side of the workpiece. (Fig. 16)

3.3 Ilustrated description

PR10E
A. Parallel guide assembly.
B. Variable speed drive.
C. Guide lock.
D. Head upper position adjustment.
E. Depth scale.
F. Depth stop.
H. Depth stop turret
I. Depth scale lock knob.
J. Safety switch control.
K. Dip block lever.
ENGLISH
remind covering the
19
L. Internal guide.
M. cutting holes device.
N. Flat key.
O. Machine base.
P. Lock button.
Q. collet nut.
R. Vacuum coupling
S Cutter shaft lock button
PR6 / PRP6
1 Loosen
2 Tighten
3 Hold
4 Base
5 Adjusting roller
6 Bit protrusion
7 Lever
8 Scale
9 Switch lever
10 Workpiece
11 Feed direction
12 Bit revolving direction
13 View from the top of the tool
14 Correct bit feed direction
15 Trimmer shoe, straight guide or
trimmer guide
16 Bolt
17 Guide plate
18 Straight guide
19 Flat washer*
20 Wave washer*
21 Wing nut
22 Clamp screw (A)
23 Centre hole
24 Nail
25 Adjusting screw
26 Clamp screw (B)
27 Trimmer guide
28 Bit
29 Guide roller
30 Screwdriver
31 Base protector
32 Screws
33 Straight bit
34 Templet
35 Distance (X)
36 Templet guide 10
37 Limit mark
38 Brush holder cap
4. Operating instructions

4.1 Placement and testing

STARTING
Hold the cutter firmly with both hands at the grips.
1. Push button/trigger to start.
2. For continuous work, press the lock button (PR10E/
PRP6).
3. To stop and unlock the machine, push the trigger again.
4. Wait for the machine achieving full speed before any
works.
5. To stop, simply release button.
19