Technical Data; Assembly - Scheppach BG200AL Traducción De La Instrucción De Original

• Do not apply coolant directly to a grinding wheel.
Coolant can weaken the bonding strentgh of the
wheel and cause it to fail.
• Sparks are a hazard. Do not grind near gas or flam-
mable liquids.
• Stand to one side of the wheel when turning on the
power. Dress the wheel on the face only. Dressing
the side of the wheel can cause it to become too
thin for safe use.
• Grinding creates heat. Do not touch the work piece
until you are sure it has cooled down sufficiently.
• Use grinding wheels that are rated for safe use on
the grinder. Do not use a wheel that is rated lower
than the grinder speed.

6. Technical Data

Dimensions L x W x H mm
ø grinding disc mm left/right
ø grinding disc bore mm
grinding disc width mm left/right
Weight kg
Motor V/Hz
Input power P1 W
Motor speed 1/min
Subject to technical changes!
Load factor:
A load factor of S2 30 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (550 W) for no longer than
30 minutes ON period. If you fail to observe this time
limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
Sound
Sound values were measured in accordance with
EN 61029.
Sound pressure level L 69.9 dB(A)
pA
Ucertainty K 3 dB
pA
Sound power level L 81.1 dB(A)
WA
Uncertainty K 3 dB
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
m Warning!
The specified vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep-
tional circumstances.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
440 x 280 x 340
200/200
15,88
25/40
16,6
230/50
550
2850
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect workin-
gorder.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Some examples of means for reducing the vibration
stress are wearing gloves while using the tool and
limiting work time. In the process all parts of the
operating cycle must be taken into account (such
as times in which the electric tool is switched off or
time in which it is switched on, but is not running
under a load).

7. Assembly

Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
Always pull the power plug before making adjust-
ments to the equipment.
Pull the power plug before doing any mainte-
nance or assembly work on the equipment.
• The machine must be set up so that it stands firmly,
i.e. it must be securely screwed to a work bench or
similar.
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• The grinding wheels must rotate freely.
• Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the equipment to the power supply.
m WARNING! Never connect the plug to power
source outlet until all installations and adjustments
are completed and you have read and understood
sthe safety and operation instructions.
Assembly
Work Rests (Fig. 1, Nr. 4)
Install the work rest with two hex screws and two
washer to the wheel guard. The distance between
wheel and work rest should not exceed 2 mm.
GB | 19