Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
English
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing the Battery Pack
(Fig. E)
nOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
9
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
WARNING: Tool may stall (if overloaded or improperly
used) causing a twist. Always expect the stall. Grip
the tool firmly with both hands to control the twisting
action and prevent loss of control which could cause
personal injury.
Proper hand position requires one hand on the handle
and the other bracing the battery to control the twisting
action of the tool.
Switch (Fig. A)
To start the motor, slide the switch
the motor, slide the switch to "O" position.
To Maintain Safe Tool Control
•
Make sure the work surface is free of nails or screws.
Cutting into a nail or screw may cause the tool to jump,
damaging the bit.
•
Never operate the tool with one hand while holding
the workpiece with the other hand. Always clamp the
material and guide the tool with both hands.
•
Do not cut material lying on a hard surface. Clearance
behind material to be cut must be allowed for
protruding bit.
•
Disconnect battery from tool before making adjustments,
changing bits, or cleaning tool.
•
Do not start the tool with bit engaged in the material.
The bit may grab the material.
10
into the tool handle, align the
8
1
to "I" position. To stop
Cutting a Hole for an Electrical Outlet
(Fig. G)
WARNING: Shut off all live electric circuits to any areas
where cut outs will be made.
1. Push any wiring deeply into the outlet box to avoid
damage from the cutting bit.
2. Before hanging the sheet covering the outlet, mark
the approximate location of the center of the outlet on
the wall board. Check the cutting bit depth against the
side of the board to be sure it will cut entirely through
the material.
3. Tack the sheet in place with a few fasteners avoiding the
stud holding the outlet. This allows the wall board to flex
slightly around the protruding fixture box.
4. Turn the cut‑out tool on. Holding the tool firmly with
both hands, plunge the bit straight into the center of
the outlet.
5. Cut to the right until the edge of the box
counterclockwise is touched. Pull out just enough for the
bit to clear the edge of the box. Plunge in again holding
the bit gently against the outside of the box.
6. Follow the outside of the box as shown keeping slight
pressure against the box. This will minimize wandering
and give you a clean precise cut.
7. Remove the waste and dust from the outlet. Finish
fastening the sheet of wall board.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
10
installing attachments or accessories. An
accidental start‑up can cause injury.
Your CRAFTSMAN power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Publicidad
Tabla de contenido
