Programming Combo Device Codes; Vcr/Dvd/Dvr Punch-Through Feature; Punch-Through; Setting Any Mode To Use Its Own Volume/Mute - Zenith ZB410B Manual Del Propietário

Setup, cont.

Programming Combo Device Codes

Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/
VCR, etc.) will require you to set up two different Mode
buttons to control both parts of the Combo device. For
example, if you have a TV/DVD Combo, you might
need to set up one code under the TV button to control
the TV part AND a separate code (under any other
Mode button) to control the DVD part.

VCR/DVD/DVR Punch-Through Feature

This remote allows the 6 VCR transport buttons (i.e.
PLAY, PAUSE, STOP, FF, REWIND, and REC) to
Punch-Through control from any Mode programmed
with TV, SAT or Cable codes to the last VCR, DVD
or DVR programmed Mode you used. Normally other
types of remotes only punch-through (from another
Mode) on the 6 VCR buttons to the device programmed
under the VCR Mode button. This is not much use if
you are using a DVD programmed under a Mode other
than VCR. For example, if you have 2 DVD, VCR or
DVR devices programmed into this remote, the last one
you accessed on the remote will be the one that has con-
trol of the 6 VCR transport buttons when in any other
Mode. This feature will not operate if the programmed
TV, SAT or Cable code has its own VCR transport but-
ton control e.g. a TV Combo, SAT/PVR, etc.
Volume/Mute Control and Punch-Through Feature
This remote lets you select which device Mode controls
your Volume/Mute buttons. The remote is initially set
(factory default) for all device Modes programmed
with "Visual" codes (e.g. TV, VCR, DVD, DVR, SAT
& CABLE) and "Audio" codes (e.g. CD & AUDIO)
to use their own Volume/Mute control if present. If
the programmed "Visual" code has no Volume/Mute
operation of its own then those buttons will punch-
through control to the TV Mode device without needing
to change to TV Mode. Please refer to the next page for
more information.
10
All manuals and user guides at all-guides.com
Setup, cont.
Any Mode chosen for Volume/Mute control MUST
have its own Volume/Mute function or the Volume/
Mute buttons will do nothing.
Setting ALL Volume/Mute Control to any one Mode
This routine can set all Modes to "punch-through" to
any one chosen Mode for Volume/Mute button control
without the needing to change to that Mode.
1. Press and hold the SETUP button until the red
indicator turns on, then release the button.
2. Press and hold the MUTE button until the red
indicator blinks off, then release the button.
3. Press and release the desired Mode button (TV,
SAT, etc.) for Volume/Mute control, the red
indicator blinks then stays on.
4. Press and release the MUTE button and the red
indicator turns off. The red indicator will blink
rapidly for three seconds if the Mode you have
selected has no Volume/Mute control.
5. All other Modes will now punch-through to your
chosen Mode for Volume/Mute control.
6. All "Visual" and "Audio" programmed Modes will
now punch-through to the respective Modes you
have chosen for Volume/Mute control.

Setting any Mode to use its own Volume/Mute

Control
This routine can set any Mode to use only its own
Volume/Mute control. Note - If your chosen Mode has
no Volume/Mute functions of its own then the Volume/
Mute buttons will do nothing.
1. Press and hold the SETUP button until the red
indicator turns on, then release the button.
2. Press and hold the MUTE button until the red
indicator blinks off, then release the button.
3. Press and release the desired Mode button (TV,
SAT, etc.), the red indicator blinks then stays on.
4. Press and release the VOLUME- (Down) button,
the red indicator blinks then stays on.
5. Press and release the MUTE button and the red
indicator turns off.
6. All "Visual" and "Audio" programmed Modes will
now punch-through to the respective Modes you
have chosen for Volume/Mute control.
11