Connecting Peripheral Equipment; Connection With A Pc; Connection With Av Equipment - Sharp PN-S525 Manual De Instrucciones

Connecting Peripheral Equipment

Caution
• Be sure to turn off the main power switch and disconnect
the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the
equipment to be connected.
• Be careful not to mix up the input terminal with the output
terminal when connecting cables. Mixing up the input and
output terminals may cause malfunctions and the other
problems.

Connection with a PC

PC1 input terminal
PC3 input terminal
PC audio input terminal
• Use a commercially available signal cable (DVI-D 24 pin)
for the PC1 input terminal. Set DVI SELECT of INPUT
SELECT on the OPTION menu to PC1 DVI-D when using
the PC1 input terminal. (See Operation guide.)
• Use a commercially available HDMI cable (conforming to
the HDMI standard) for the PC2 input terminal. Set HDMI
SELECT of INPUT SELECT on the OPTION menu to PC2
HDMI when using the PC2 input terminal. In addition,
select the audio input terminal to be used in HDMI AUDIO
SELECT of INPUT SELECT on the OPTION menu. (See
Operation guide.) When DIGITAL is selected, connection to
the PC audio input terminal is unnecessary.
• Use a commercially available signal cable (Mini D-sub
15 pin) for the PC3 input terminal.
• Use a commercially available signal cable (BNC) for the
PC4 input terminals. Set BNC SELECT of INPUT SELECT
on the OPTION menu to PC4 RGB when using the PC4
input terminals. (See Operation guide.)
• Use a commercially available audio cable (mini stereo jack)
for the PC audio input terminal. Use an audio cable without
resistance.
TIPS
• Images may not be displayed properly depending on the
computer (graphics board) to be connected.
• A screen with 1920 x 1080 resolution may not be displayed
correctly on PC4. In this case, check the settings of your
computer (graphics board) to verify that input signals
conform to specifications of this monitor. (See page 17.)
• If there is a check box to disable EDID in display control
panel, check it when using PC4.
• Use the automatic screen adjustment when a PC screen is
displayed for the first time using PC3 or PC4, or when the
setting of the PC is changed. (See Operation guide.)
The screen is adjusted automatically when SELF ADJUST
in the OPTION menu is set to ON. (See Operation guide.)
10
E
PC2 input terminal
V H
R G B
PC4 input terminals

Connection with AV equipment

AV1 input AV2 input
terminal
AV4 input terminal
AV audio input terminals
• Use a commercially available signal cable (DVI-D 24 pin)
for the AV1 input terminal. Set DVI SELECT of INPUT
SELECT on the OPTION menu to AV1 DVI-D when using
the AV1 input terminal. (See Operation guide.)
• Use a commercially available HDMI cable (conforming to
the HDMI standard) for the AV2 input terminal. Set HDMI
SELECT of INPUT SELECT on the OPTION menu to
AV2 HDMI when using the AV2 input terminal. In addition,
select the audio input terminal to be used in HDMI AUDIO
SELECT of INPUT SELECT on the OPTION menu. (See
Operation guide.) When DIGITAL is selected, connection to
the AV audio input terminal is unnecessary.
• Use a commercially available component cable (BNC)
for the AV3 input terminals. Set BNC SELECT of INPUT
SELECT on the OPTION menu to AV3 COMPONENT when
using the AV3 input terminals. (See Operation guide.)
• Use a commercially available S-video cable for the AV4
input terminal.
• Use a commercially available video cable (BNC) for the
AV5 input terminal.
• Use a commercially available audio cable (RCA) for the AV
audio input terminals.
• The AV1/AV2 input terminals are compatible with the video
signals below:
1920 x 1080 p @ 50/59.94/60 Hz
1920 x 1080 i @ 50/59.94/60 Hz
1280 x 720 p @ 50/59.94/60 Hz
720 x 576 p @ 50 Hz
720 x 480 p @ 59.94/60 Hz
640 x 480 p @ 59.94/60 Hz
• The AV2 input terminal is also compatible with the video
signals below:
1920 x 1080p @ 24Hz
720(1440) x 576i @ 50Hz
720(1440) x 480i @ 59.94/60Hz
• The AV3 input terminals are compatible with the video
signals below:
1080p @50/60Hz, 1080i @50/60Hz, 720p @50/60Hz,
576p @50Hz, 576i @50Hz, 480p @60Hz, 480i @60Hz
Cr/Pr Y Cb/Pb
AV3 input
terminal terminals
AV5 input terminal