Section 3. Installation; Setup; Tools; Power Supply - Jandy TruDose Manual De Instalación Y Funcionamiento

Page 12
ENGLISH

Section 3. Installation

3.1

Setup

1. Turn off all peripheral equipment such as heaters
and pumps.
2. Relieve pressure from the filtration system.
3.2

Tools

• Cordless drill
• 1/4" NPT Tap (provided)
• 7/16" drill bit
• Masonry drill bit and anchors or other appropriate
fasteners.
• 13/16" wrench or channel-lock pliers
• Water-tight outlet cover for outdoor installations
3.3

Power Supply

• The TruDose Chemical Controller needs to be
connected to a GFCI protected watertight outdoor
outlet.
• Do not use extension cords.
• The power supply must be installed at least 1 ft
(30cm) above the ground surface. Ensure the power
supply is protected from direct water exposure from
sprinklers, water runoff from rooftops and drainage.
ATTENTION
The controller must be powered only with the provided
power supply, and connected to a dedicated GFCI
protected electrical circuit, Class A GFCI in Canada. No
other equipment, lights, appliances, or outlets may be
connected to the controller circuit.
3.4

Controller Installation

3.4.1 Location
• Wall area with easy access
• At least 5 feet (1.5 m) horizontally from the edge of
the pool and/or spa. In Canada, at least 3 meters (10
feet) horizontally from the edge of the pool and/or
spa.
• Within 15 feet of GFCI power source
CAUTION
In order to avoid premature failure or damage to the
controller, protect the controller from direct water exposure
from sprinklers, water runoff from rooftops and drainage,
etc. Failure to comply may cause controller failure, and
may void the warranty.
• The TruDose Controller must be installed at least
2 feet (0.6 m) vertically off the ground surface.
Ensure the controller is protected from direct water
exposure from sprinklers, water runoff from rooftops
and drainage.
Jandy TruDose Chemical Controller
® TM
3.4.2 Mounting
NOTE: The controller and flow cell are factory
mounted to the ABS board for your
convenience.
1. Securely mount ABS mounting board with the
chemical controller and flow cell on the wall.
2. Drill a 7/16" hole and tap a 1/4" NPT port to a
location downstream from the filter and upstream
from any heater or chemical introduction point.
Install a tubing connector (included) and 3/8" flex
tubing to be connected to the left side flow cell port
containing the flow switch. The in-line filter will
also be installed in this line in an easily-accessible
location.
NOTE:
Verify that the in-line filter is installed with
directional arrows pointing in the direction of the
flow (towards flow cell).
3. Drill a 7/16" hole and tap a 1/4" NPT port to a
location that is subject to vacuum or reduced
pressure. Install a tubing connector (included) and
3/8" flex tubing to be connected to the right side
flow cell port.
NOTE:
We recommend that this tubing connector be
installed into the drain hole on the suction side
of the pump for best performance.
4. Cut 3"-6" length of 3/8" flex tubing and insert into
the flow cell's sample stream port (center).
3.5 pH and ORP Sensors
Installation
NOTE: Carefully unpack the pH and ORP sensors and
set aside in a clear area until ready to install into
the flow cell.
1. Verify that the controller power is off.
2. Carefully remove the plastic protective container
from the sensors and store in a separate location for
future re-use.
3. Loosen (do not remove) the top nut of the
compression fittings at the top of the flow cell and
carefully slide the glass end of each sensor (pH
and ORP) into the compression fittings. Ensure
that the tip is submerged into the water to within
1/2" from the bottom of the flow cell. Hand tighten
each nut fitting. Do not use any tools to tighten the
compression fittings.
4. Electrical Connections
• Verify that the controller is off.
• Connect the pH sensor connector (blue) to the left
BNC connector on the bottom of the controller.
• Connect the ORP sensor (red) to the right BNC
connector on the bottom of the controller.
• Plug power supply into the GFCI protected outlet
(outdoor installations should have weather proof
enclosures installed).
NOTE: Continue to monitor free chlorine with manual
testing to ensure proper sanitation levels.
|
Installation & Operation Manual