Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

5. Turn the volume control on main unit or press the volume buttons on remote control to adjust to the desired volume
level.
FM / FM STEREO RECEPTION
When listening to the FM radio, press the ST./MONO button on remote control to switch between stereo mode and mono
mode. The FM stereo icon "ST" appears on the display when unit is set in stereo mode. It is preferable to receive the program
in mono when you are receiving a weak station.
HINTS FOR BEST RECEPTION:
For best FM reception, the FM wire antenna located on the back of the unit should be fully unwrapped and extended.
NOTE: Automatic tuning depends on the signal strength of the broadcasting station, so weak stations may be skipped. You
can manually tune to find the weak stations if a station gets skipped. With strong signals, the tuner may stop before it reaches
the actual broadcast frequency, so you may need to manually tune for the best reception.
1. Press the POWER button on main unit or remote control to turn on the unit.
2. Press the SOURCE Button on main unit or remote control to select FM radio mode.
3. Press and hold the TUNE
display. Release the button for auto search & program preset channels. Auto searching and program will stop at P01 after
scan finished.
Note: If the channels stored during the auto search & program preset are not the ones you want to save, use the method
below for manually saving radio presets.
4. Tune to the desired radio station either by "manually" or "automatically" tuning method.
5. Press the PROG. button on the remote control, the next available preset memory number and a flashing number will show
on the LCD display (Note: "P01" will show in the display if you are programming a preset for the first time).
6. Tap the CHANNEL -/+ buttons on main unit or remote control to select the preset number you want to assign the station
to.
7. Tap the PROG. button on the remote control to confirm the setting.
8. Repeat above steps 4 - 8 to preset up to 30 FM stations.
RECALLING PRESET MEMORY CHANNELS
In radio mode, recall the pre-set channels by pressing the CHANNEL -/+ buttons on main unit or the numbers on remote
control.
Note:
Besides commercial CDs, this CD player will also play self-compiled CD-R/RW, MP3 discs. Do not attempt to play CD-ROM,
CDI, VCD, DVD or computer CDs.

IMPORTANT:

It may take up to 10 seconds for the actual playback to begin. If playback does not start at all, it is possibly due to the quality
of the CD-R/RW, MP3 disc and/or the compatibility of the CD compilation software. The manufacturer is not responsible for
the playback quality of CD-R/RW, MP3 discs.
Do not stick a label to either side of the disc. It may cause a serious malfunction.
PLAYING CD
1. Press the POWER/STANDBY button on main unit or remote control to turn the unit on.
2. Press the SOURCE button on remote control or main unit to select CD mode and press "Open/close disc compartment" (on
top of the compartment lid).
3. Place a CD on the center spindle with its label side facing out towards the CD lid. Close the disc compartment.
4. The unit starts to read the disc, "---" flashes on the display. After a few seconds, the total number of tracks show on the
LCD display.
5. Press the PLAY/PAUSE button on main unit or remote control, PLAY indicator
playing the first track.
6. Turn the volume control on main unit or press the volume control buttons on the remote control to adjust to the desired
volume level.
7. To pause playback, press the PLAY/PAUSE button on main unit or remote control. The track time will be paused and the
play indicator
will blink on the display. To resume playing, press the PLAY/PAUSE button again.
8. You can choose to play your favorite track by pressing the SKIP NEXT
display will indicate the current track number.
9. To locate a particular section within a track, press and hold the
button to continue playing your selection.
10. To stop playing, press the STOP ◼ button.
PLAYING CD-R/RW, MP3 WITH FOLDER
1. Press the SOURCE button on the remote control, and load an MP3 disc.
2. Press the FOLDER -/+ button to select desired playback folder.
3. Select the desired file to be played by pressing the SKIP NEXT
4. Press the PLAY/PAUSE button. Playback will start and the file name will be displayed.
or TUNE
button on the main unit or remote control until "SCA" readout appears on the
shows on the display, the CD will start
button or SKIP PREVIOUS
or
button until the section is found. Release the
or SKIP PREVIOUS
7
button. The LCD
button.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

102.326

Tabla de contenido