Safety Instructions For All Operations - Black and Decker WP1500K Manual De Instrucciones

making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main voltage
corresponds to the voltage on the rating plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
BLACK+DECKER Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by
BLACK+DECKER, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Hz ....... Hertz
Read
Instructions
W ........ Watts
Manual
min ..... minutes
Use Eye
Protection
..... Alternating
Current
Use Ear
Protection
..... Direct
Current
V ........ Volts
n ....... No-Load
0
Speed
A ........ Amperes
FEATURES (Fig. A)
1. On/off switch
2. Variable speed switch
3. Lock-on button
4. Side handle
5. Spindle lock
All manuals and user guides at all-guides.com
Warnings common security for all grinding
operations, grinding and brushing with a wire brush
and polishing.
a. This power tool is intended to function as a
b.
c. Do not use accessories which are not specifically
d. The rated speed of the accessory must beat least
e. The outside diameter and the thickness of your
f.
g. Do not use a damaged accessory. Before each
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
h. Wear personal protective equipment. Depending
ENGLISH • 13
SAFETY INSTRUCTIONS FOR ALL
OPERATIONS
grinder. Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious
injury.
Operations such as cutting-off, sander, wire
brush or polisher are not recommended to be
performed with this power tool. Operations for
which the power tool was not designed may create a
hazard and cause personal injury.
designed and recommended by the tool
manufacturer. Just because the accessory can
be attached to your power tool, it does not assure safe
operation.
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated
speed can break and fly apart.
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories
cannon be adequately guarded or controlled.
The arbour size of wheels, flanges,backing pads
or any other accessory must properly fit the
spindle of the power tool. Accessories with arbour
holes that do not match the mounting hardware of the
power tool will run out of balance, vibrate excessively
and may cause loss of control.
use inspect the accessory such as abrasive wheel
for chips and cracks, backing pad for cracks,
tear or excess wear, wire brush for loose or
cracked wires. If power tool or accessory is
dropped, inspect for damage or install an
undamaged accessory. After inspecting and
installing an accessory, position yourself and
by standers away from the plane of the rotating
accessory and run the power tool at maximum
no-load speed for one minute. Damaged
accessories will normally break apart during this test
time.
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
mask, hearing protectors, gloves and workshop
apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be