Pahlen WIDE Manual Del Usuario página 8

Skimmer WIDE
General installation instruction
Place the skimmer into the pool framework according to your pool supplier's instructions. The skimmer is typically placed at the
opposite side of the water inlet. During installation works, stainless steel tools with clean contact surfaces should be used.
In order to avoid scratches and stains, keep items in their original packaging until installation.
Be careful during installation, so as not to scratch the skimmer.
For the pool framework made of wood, metal or plastic - finished with pool liner
1 2
1 1
Bild 1.
Installation as following:
1. Make a hole for the skimmer in the framework,
dimensions and placement as shown in Figure 2.
2. Mount and secure the skimmer in the pool
framework, position as shown in Figure 2.
The water surface should be at the centre of the
opening and the flange of the skimmer should be
in line with a finished pool wall.
To avoid subsidence, sand should be packed around and below the skimmer, or fix the skimmer with e.g. pressure-treated
joists in the pool frame.
3. Connect the pipe coupling to the pool circulation with an appropriate thread sealant.
4. The openings are for level control, overflow and refill should be at the rear plugs if they are not used.
5. Check that the flap cap is properly in place and can move.
6. Attach the self-adhesive packing onto the skimmer front edge (towards the pool).
7. Add the pool liner.
8. Fill the pool with so much water that it reaches 5 cm below the skimmer. Turn off the water.
9. Cut a small incision in the liner middle in the skimmer. Install the outer packing and the mounting frame - secure them first,
then tighten crosswise.
10. Cut clean the pool liner gently along the front/inside the mounting frame.
11. Continue to fill the water into the pool until its level reaches the center of the skimmer opening.
12. Install the front.
13. Adjust the skimmer to the desired height in relation to the flooring around the pool.
Fix the skimmer with attached straps.
In case of machining the
tool exclusively for stain-
less steel material should
be used.
3 4 5 8 10 11
1 7 1 5 1 1
6 9
1 1
7
6

6,5 (4x)
Surface treatment
E
The tolerance class in accordance with this Assembly drawing no.
part of ISO 2768-mK
Bräddavlopp WIDE
Sid 2
Installationsbild
Trä-, plåt-, plaststomme/liner
Box 728, SE-194 27 Upplands Väsby, Sweden
Phone +46 8 59411050, Fax +46 8 59086880
C-C ( 1 : 3 )
12
1
1. Fixing strip with a screw M5x12 (2 pcs)
2. Pipe
3. Nut M6 (4x)
4. Frame
5. Countersunk screw M6x30 (4 pcs)
6. Self-adhesive packing 1.5 mm
7. Wall mat
8. Liner
9. Packing 2 mm
10. Mounting frame
11. Countersunk screw M5x12 (26 pcs)
12. Frоnt
13
Designed by: Drawn by: Date Approved by:
TK 2016-11-10
Art.no.
Scale Revised by: Date
Drawing number Rev.no.
M12624 0
A
Flap cap
Support for
the skimmer.
8
Surface treatment
E
The tolerance class in accordance with this
ENGLISH
Bottom pool frame
461
435
Water surface
Frame
Wall mat
Plywood
A
Designed by: Drawn by: Date
TK
Assembly drawing no. Art.no.
Underkant sarg
* Fro
från
Fig 2.
Surface treatment
E
The tolerance class in a
part of ISO 2768-1
Box 728, SE-194 27 Upplands Väsby, Swe
Fig 3.
Phone +46 8 59411050, Fax +46 8 590868
Liner
Front
Approved by:
2016-11-10