Die Set User Manual - GBC MFPP-C1 Manual De Instrucciones De Operación

8. DIE SET USER MANUAL

The MFPP-C1 accepts Punch and Crease dies. Punch dies must be
configured for the paper size being processed. Crease dies do not need
configuring.
Glossary
LEF- Long Edge Feed- Indicates that the paper is being fed through the
machine so that the longer side of the sheet will be punched.
SEF- Short Edge Feed- Indicates that the paper is being fed through the
machine so that the shorter side of the sheet will be punched.
Statement (STMT) Paper- 8.5" X 5.5"
Legal Paper- 8.5" X 14"
Ledger Paper- 11" X 17"
Punch Dies
The punch die sets for the MFPP-C1 are intended to work with multiple
paper sizes and sheet feed directions. In order to accommodate different
sheet sizes, the die set must be configured to the correct number of
punching pins and the die stop must be set to the proper position. The
die label contains information on the common paper punching sizes, for
the uncommon sizes please refer to Table 1.
Pin Numbering
Die punching pins are numbered sequentially starting from the handle
end. Figure 8.1 shows a 47 hole coil die as an example. All square and
round hole die sets follow the same pin numbering format.
Pin #47
Figure 8.1 Coil Die Set Pin Numbering
Figure 8.2 Pressure Bar Removal
Pin Removal
Coil
Rnd
Rnd/Sq
US Paper Sizes
Canon Part Number 7714012 7714014
7714029 7714025
LTR LEF 2, 47 1, 23
LTR SEF 7, 42 NONE
STATEMENT LEF 7, 42 NONE
LEGAL SEF 7, 42 NONE
LEDGER SEF 2, 47 1, 23
9" x 12" LEF 1, 2, 47 1, 23
9" x 12" SEF 6, 7, 42, 43 3, 21
Coil
Rnd
Rnd/Sq
ISO Paper Sizes
Canon Part Number 7714013 7714014
7714029 7714026
A4 LEF NONE NONE
A4 SEF 7, 41 4, 21
A5 LEF 7, 41 4, 21
A3 SEF NONE NONE
SRA4 LEF NONE NONE
SRA4 SEF 6, 7, 42, 41 4, 21
*For CombBind 20H configuration pull Pin Number 1.
The above chart shows the information on which pins need to be removed to correctly punch each sheet size and configuration that the MFPP-B1 can accept.
For standard offering dies not found in the chart no pin adjustment is necessary.
Pin #1
Quarter Turn
astener
Wire Wire
3 Hole
2:1 3:1
8mm
Rnd/Sq
Pin Numbers to Remove Based On Paper Size or Orientation
7714015 7714016
7714027
1, 34 NONE 3H/5H/7H
5, 31 N/A N/A
5, 31 N/A N/A
5, 31 N/A N/A
1, 34 NONE 3H/5H/7H
1, 34 NONE 3H/5H/7H
5, 31 N/A N/A
Wire Wire
3 Hole
2:1 3:1
8mm
Rnd/Sq
Pin Numbers to Remove Based On Paper Size or Orientation
7714015 7714016
7714028
NONE N/A N/A
5, 30 N/A N/A
5, 30 N/A N/A
NONE N/A N/A
NONE N/A N/A
4, 5, 30, 31 N/A N/A
Table 8.1 Pin Removal Guide
To remove punch pins from the punch die first turn the two Quarter Turn
Fasteners counter clockwise to release the pressure bar. Remove the
pressure bar and set aside.
Lift up and remove the desired pins according to Table 8.1. Store pins in
the pin storage tray inside front door of machine making sure pins cannot
be dropped, damaged or lost while removed.
Replace the pressure bar by lining up dowel pin holes with exposed
dowel pins. Hold pressure bar so that it is seats completely over dowel
pins and then rotate Quarter Turn Fasteners clockwise until a click is felt
to lock pressure bar in position.
Important! Make sure pressure bar is attached and both Quarter Turn
Fasteners are in the locked position prior to inserting the die set into the
machine or serious damage can occur to both the machine and die set.
3/5/7 2/4 2/4
Hole Hole Hole
8mm 8mm 6.5mm
7714017 7714018 7714019
N/A N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A
N/A N/A
3/5/7 2/4 2/4
Hole Hole Hole
8mm 8mm 6.5mm
7714017 7714018 7714019
2H/4H 2H/4H
2H 2H
2H 2H
2H/4H 2H/4H
2H/4H 2H/4H
N/A N/A
MFPP-C1
Figure 8.3 Pressure Bar
Figure 8.3 Pin Removal
Dowel Pin Holes
Figure 8.4 Replace Pressure Bar
2/4 VeloBind VeloBind
Hole 11 Hole 12 Hole
SCAN LTR A4
7714020 7714021 7714022
N/A NONE N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A NONE N/A
N/A NONE N/A
N/A N/A N/A
2/4 VeloBind VeloBind
Hole 11 Hole 12 Hole
SCAN LTR A4
7714020 7714021 7714022
NONE N/A NONE
NONE N/A N/A
NONE N/A N/A
NONE N/A NONE
NONE N/A NONE
NONE N/A N/A
GB
eWire
CombBind
Rnd/Sq
7714023 7714030
7714031
1, 21 1, 34
NONE N/A
NONE 5, 31
NONE 5, 31
1, 21 1, 34
1, 21 1, 34
3, 19 5, 31
eWire
CombBind
Rnd/Sq
7714024 7714030
7714031
NONE NONE
4, 19 5, 30
4, 19 5, 30
NONE NONE
NONE NONE
4, 19 4, 5, 30, 31
11