WERKU WK401630 Instrucciones Originales página 4

ENG
components Avoid inhaling these substances
►
or allowing them to come into contact with your
skin Use PPE designed to prevent and protect
►
against incidents of this kind.
DESCRIPTION OF THE PRODUCT.
The cordless demolition hammer drill has
►
been designed to carry out jobs of drilling with
percussion on concrete, brick and stone, as well
as drilling without percussion on wood, metal,
ceramics and synthetic materials
plan to familiarize yourself with the cordless
demolition hammer drill before use.
1
2
1. Chuck.
2. Auxiliary handle.
3. Handle.
4. Switch.
5. Battery.
6. Turn selector.
7. LED lamp.
8. Function selector.
USE INSTRUCTIONS.
Before starting up the cordless demolition hammer
►
drill, we recommend that you carefully read all of
the instructions as indicated
regulations regarding the prevention of accidents,
health and safety directives, laws and applicable
restrictions for work places
hammer drill must only be used by persons who
have been instructed in its use and only for the
purposes for which it has been designed.
POWER SUPPLY.
Make sure the power supply is adapted to the
►
requirements shown on the information panel of the
cordless demolition hammer drill (1)
at low voltage will make it operate slowly
reduce performance and may cause the motor to
overheat.
Refer to this
►
8 6
7 5 4
Please respect all
►
The cordless demolition
►
Using the motor
►
This will
►
BATTERY AND CHARGER.
If the battery housing is damaged, do not insert
►
it in the charger, as there may be a risk of electric
shock The charger and battery are designed to
►
work together, do not attempt to charge the battery
with any other model of charger
the charger to damp conditions
is designed for use with rechargeable batteries,
any other type of use may pose a fire risk or
cause electric shocks
from sources of heat
incorrect reassembly may increase the risk of fire,
explosion or electric shocks
to enter the charger, as they may cause electric
shocks Do not store the charger or the batteries
►
in temperatures higher than 40ºC
charger at a different voltage to that specified by the
manufacturer
3
under any circumstances
batteries, even when they are empty or broken, as
they may explode
air temperatures any lower than 4.5ºC or higher
than 40.5ºC to prevent damage
and battery may heat up during the charging
process, this is normal, and does not mean there is
a problem
►
does not produce enough energy in situations when
it previously did, do not use the battery in these
conditions
►
when it does not have a battery inserted.
BATTERY INSTALL.
To remove the battery hold the cordless
►
demolition hammer drill firmly by the handle, press
the battery catch and remove it (2)
battery checking that the correct polarities are
used (3).
CHARGING BATTERY.
Insert the charger plug into the battery
►
the charger to the power supply
to charge the battery fully at 20ºC
overheats as a result of direct sunlight or other
factors, the pilot light may not illuminate
leave the battery to cool and then restart the charging
process Disconnect the charger from the power
►
supply Hold the battery firmly and pull the charger
►
plug out Due to their internal chemical composition,
►
batteries that have never been used or left unused for
long periods of time may not produce their full output
during their first or second use
phenomenon, to restore the optimal battery activity,
repeat this process three times with each of them.
4
English
►
The charger
►
Keep the charger away
►
Do not open the charger,
►
Do not allow liquids
►
►
The batteries must not be opened
►
Do not attempt to burn
►
Do not charge the batteries in
►
Both the charger
►
The battery must be recharged when it
Disconnect the charger from the mains
IIt will take 2 hours
►
►
This is a temporary
►
Do not expose
Never use the
Insert the
►
Connect
►
If the battery
In this case,
►