Milwaukee 2848-20 Manual Del Operador página 5

NOTE: If the current pressure item to be inflated
is greater than the target pressure, the tool will not
begin inflation.
7. To start, press the Inflation
minimum setting for the automatic stop feature is
10 PSI.
8. The tool will shut off automatically once the target
pressure has been reached.
NOTE: Inflation may continue after Auto Pressure
Check Feature is engaged to hit the most accurate
results.
NOTICE: To avoid tool damage from overheating,
allow tool to cool for 40 minutes after each 20 minutes
of continuous use.
9. To stop, press the Inflation
button.
NOTE: The tool will shut down after 5 minutes of
inactivity.
NOTE: The tool's cooling fan will run until the pump
head cools or the tool is turned off.
Manual Inflate
The inflator can also be used to manually inflate
items. When a target input value is not set, the
inflator will show 0 PSI. Press and hold the inflation
UNITS
button until desired pressure is reached. When the
inflation button is released, inflation will stop. For
MEMORY
small inflatables and bike tires it is recommended to
use manual inflate mode for most accurate results.
NOTE: For anything under 10 PSI, manually inflate
the item using the manual Inflate mode.
Memory Settings
To view memory settings, press the memory button
to navigate through memory slots M1 - M4. After
reaching memory slot M4, pressing the memory
button again will return to the homescreen.
To adjust memory settings:
1. Press the memory button to navigate to the desired
M1 - M4 memory slot.
2. Press or to adjust to the desired inflation
value.
3. Press and hold the memory button for 2 seconds
to store the pressure in the current memory slot.
To inflate to a saved memory setting:
1. Press the memory button to navigate to the de-
sired M1 - M4 memory slot.
2. Press the inflation button.
NOTE: The actual value indicator will increase until
it reaches the saved memory value.
Troubleshooting
If pressure accuracy becomes poor or the inflator's
actual value reads greater than zero when not con-
nected to any object, the pressure sensor may have
drifted due to altitude or other factors.
To re-zero:
With nothing connected to the inflator, hold
the and the Inflation
to re-zero the pressure.
NOTE: This function will re-zero up to 5 PSI.
Sports Needle/Raft Nozzle
Insert needle or nozzle onto the inflator. Attach to the
item. Be careful not to bend the accessory. Remove
after inflation.
Presta Valve
Use the Presta valve with Presta valve stems. Before
inflating, loosen the locking nut on the valve stem.
Once inflation is complete, tighten the locking nut to
seal the valve.
button. The
button or power
button for 3 seconds
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Clean dust and debris from any vents. Keep tool
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
For repairs, return the tool, battery pack and charger
to the nearest authorized service center.
ACCESSORIES
Use only recommended accesso-
WARNING
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
5
Cleaning
Repairs
(1.800.729.3878)