EINHELL TP-CD 18 Li BL Manual De Instrucciones página 12

6. Operation
6.1 Torque setting (Fig. 2/Item 1)
Caution! Only ever adjust the torque setting
ring when the equipment is at a standstill.
The cordless drill/driver is fi tted with a mechanical
torque selector.
The torque for a particular screw size is set
with the torque setting ring (1). The torque is
dependent on a number of factors:
•
On the type and hardness of the material
involved.
•
On the type and length of the screws used.
•
On the requirements that the screw
.connection has to satisfy.
The tool will stop rotating as soon as the set
torque is reached during operation reached.
6.2 Drilling (Fig. 2/Item 1)
For drilling purposes, adjust the torque setting
ring for the torque to the last setting "Drill". In the
drill setting the slip coupling is non-functional. The
maximum torque is available for drilling.
6.3 Changeover switch (Fig. 3/Item 3)
The slide switch above the On/Off switch is for
setting the direction of rotation of the cordless
drill/driver and for preventing the cordless drill/
driver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation. To avoid causing damage to
the gearing, the direction of rotation must only be
changed when the equipment is at a standstill.
When the slide switch is in the middle position,
the On/Off switch is blocked.
6.4 On/Off switch (Fig. 3/Item 4)
Infi nitely variable speed control is possible with
the On/Off switch. The further you push the
switch, the higher the speed of the cordless drill/
driver.
6.5 Switching from speed 1 to speed 2
(Fig. 2/Item 6)
You can work with a higher or lower speed
depending on the position of the selector switch.
Change the gear only when the drill is at a
standstill. If you fail to observe this point, the
gearing may be damaged.
Anl_TP_CD_18_Li_BL_SPK7_USA.indb 12 Anl_TP_CD_18_Li_BL_SPK7_USA.indb 12
EN
6.6 Battery capacity indicator (Fig. 4 / item 2)
Press the battery capacity indicator switch (12).
The battery capacity indicator (2) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The temperature of the battery is too low. Remove
the battery from the device and leave it at room
temperature for a day. If the error occurs again,
this means that the battery has been completely
depth-discharged and is defective. Remove the
battery from the device. Never use or charge a
defective battery.
6.7 LED lamp (Fig. 4/Item 9)
The LED light (9) can be used in poor lighting
conditions to illuminate the area where you want
to drill or screw. The LED light (9) will come on
automatically as soon as you press the On/Off
switch (4).
6.8 Changing the bit (Fig. 5)
Caution! Set the changeover switch (3) to its
center position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the cordless drill/driver.
•
The cordless drill/driver is fitted with a quick-
action chuck (8) with an automatic spindle
stop.
•
Open the chuck (8). The chuck opening (11)
must be large enough to hold the tool (drill bit
or screwdriver bit).
•
Select the suitable tool. Push the tool as far
as possible into the chuck opening (11).
•
Tighten the chuck (8) and then check that the
tool is secure.
6.9 Screws
It is advisable to use self-centering screws (e.g.
cross recessed head) as these will enable you to
work safely and reliably. Always make sure that
the bit used is of the same size and shape as the
screw. Set the torque to suit the screw size as
specifi ed in the instructions.
- 12 -
03.05.2022 13:17:46 03.05.2022 13:17:46