LAUNCH TECH X-PROG 3 Guia De Inicio Rapido página 2

Safety Instructions
Before using this test equipment, please read the following safety information carefully.
Always perform automotive testing in a safe environment.
Ÿ
Do not connect or disconnect any test equipment while the ignition is on or the engine is
Ÿ
running.
DO NOT attempt to operate the tool while driving the vehicle. Have second personal
Ÿ
operate the tool. Any distraction may cause an accident.
Ÿ Before starting the engine, put the gear lever in the Neutral position (for manual
transmission) or in the Park (for automatic transmission) position to avoid injury.
NEVER smoke or allow a spark or flame in vicinity of battery or engine. Do not operate
Ÿ
the tool in explosive atmospheres, such as in the presence of flammable liquids, gases,
or heavy dust.
Keep a fire extinguisher suitable for gasoline/chemical/electrical fires nearby.
Ÿ
Wear an ANSI-approved eye shield when testing or repairing vehicles.
Ÿ
Put blocks in front of the drive wheels and never leave the vehicle unattended while
Ÿ
testing.
Use extreme caution when working around the ignition coil, distributor cap, ignition wires
Ÿ
and spark plugs. These components create hazardous voltage when the engine is
running.
To avoid damaging the tool or generating false data, please make sure the vehicle
Ÿ
battery is fully charged and the connection to the vehicle DLC (Data Link Connector) is
clear and secure.
Automotive batteries contain sulfuric acid that is harmful to skin. In operation, direct
Ÿ
contact with the automotive batteries should be avoided. Keep the ignition sources away
from the battery at all times.
Ÿ Keep the tool dry, clean, free from oil, water or grease. Use a mild detergent on a clean
cloth to clear the outside of the equipment when necessary.
Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine
Ÿ
parts.
Store the tool and accessories in a locked area out of the reach of children.
Ÿ
Do not use the tool while standing in water.
Ÿ
Do not expose the tool or power adaptor to rain or wet conditions. Water entering the tool
Ÿ
or power adaptor increases the risk of electric shock.
Ÿ Please use the included battery and power adaptor. Risk of explosion if the battery is
replaced with an incorrect type.
Because there are various procedures, techniques, tools, and parts for servicing
Ÿ
vehicles, as well as the skill of the person doing the service work, the technician must be
well knowledgeable of the vehicle and the system being tested.
Ÿ The vehicle parts and the X-PROG 3 components are welded at a constant temperature.
Ÿ When welding vehicle parts with the X-PROG 3 components, the unit is powered off and
is grounded.
Copyright Information
Copyright © 2021 by LAUNCH TECH CO., LTD (also called LAUNCH for short). All rights
reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying,
recording or otherwise, without the prior written permission of LAUNCH.
Statement: LAUNCH owns the complete intellectual property rights for the software used
by this product. For any reverse engineering or cracking actions against the software,
LAUNCH will block the use of this product and reserve the right to pursue their legal
liabilities.
Disclaimer of Warranties and Limitation of Liabilities
All information, illustrations, and specifications in this manual are based on the latest
information available at the time of publication.
The right is reserved to make changes at any time without notice. We shall not be liable
for any direct, special, incidental, indirect damages or any economic consequential
damages (including the loss of profits) due to the use of the document.
FCC Statement
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Precautions & Disclaimer