Switching The Lamp On / Off; Twilight Sensor; Changing The Light Bulb - LIVARNO home 14160605L Instrucciones De Montaje, De Uso Y De Seguridad

Insert the wall plugs
(see Fig. D).
Guide the mains connection cable (external)
through the rubber membrane of the connection
box . Make sure that the double insulation of
1
the mains connection cable (external)
at least 8 mm into the connection box
Secure the connection box
screws (see Fig. E). Be aware of the "Up"
8
marking.
Now use the lustre terminal
light's connection cable
nection cable (external)
wire of the mains connection cable (external) is
properly connected in the correct place: live
wire, black or brown = symbol L, neutral wire,
blue = symbol N, protective earth wire, green,
yellow = (see Fig. F).
Secure the lamp body
screws on the connection box
5
Screw the decorative screw
rative cover from below (see Fig. H).
10
Mount the light bulb
into the bulb socket.
Secure the lamp head
using the fixing screws
14160705L:
Remove the lamp head screws
connection box
1
(see Fig. B).
Use the slotted holes on the connection box
intended for the screws
the drilling holes (see Fig. C).
Now drill the mounting holes (approx. Ø 6 mm,
depth approx. 40 mm). Be sure not to damage
the mains connection cable.
Insert the wall plugs
(see Fig. D).
Guide the mains connection cable (external)
through the rubber membrane of the connection
box . Make sure that the double insulation of
1
the mains connection cable (external)
at least 8 mm into the connection box
Secure the connection box
screws (see Fig. E). Be aware of the "Up"
8
marking.
into the drill holes
7
extends
6
.
1
using the included
1
to connect the
2
to the mains con-
9
. Ensure that each
6
using the correct
4
(see Fig. G).
1
onto the deco-
11
by turning it clockwise
14
on the lamp body
13
(see Fig. I).
12
and take the
15
out of the wall cover
3
as a guide to mark
8
into the drill holes
7
extends
6
.
1
using the included
1
Prior to first use / Changing the light bulb
Now use the lustre terminal
light's connection cable
nection cable (external)
6
wire of the mains connection cable (external) is
properly connected in the correct place: live
wire, black or brown = symbol L, neutral wire,
blue = symbol N, protective earth wire, green,
yellow = (see Fig. F).
Secure the lamp head
screws on the connection box
15
Screw the decorative screw
rative cover
10
Mount the light bulb
into the bulb socket.
Secure the lamp body
using the fixing screws
13
Reinstall the fuse or switch on the circuit
breaker in the fuse box (I setting) (see Fig. K).
Your light is now ready to use.

Switching the lamp on / off

Use the wall switch to switch the light on or off.
4

Twilight sensor

The light bulb has a twilight sensor. When twilight
14
begins, the light switches on automatically. When
it gets light (daylight), the light will automatically
switch off.
1
Note: When selecting the setup location, ensure
that the twilight sensor of the light bulb
affected by other light sources, e.g. street lighting.

Changing the light bulb

Switch the lamp off.
6
SHOCK!
First disconnect the lamp from the mains. To do
this, remove the fuse or switch off the circuit
breaker in the fuse box (0 setting) (see Fig. A).
CAUTION! RISK OF BURNS DUE TO
HOT SURFACES!
First, allow the lamp to cool down completely.
to connect the
2
to the mains con-
9
. Ensure that each
6
using the correct
13
(see Fig. G).
1
onto the deco-
11
from below (see Fig. H).
by turning it clockwise
14
on the lamp head
4
(see Fig. I).
12
14
DANGER OF ELECTRIC
GB/IE
is not
17