Other Connectors - JBL SYNTHESIS SDR-38 Manual

Other Connectors

ETHERNET
OUTPUT1 ZONE2
OUTPUT2 PVR UHD
eARC Serial connector OUT
USB 5V/0.5A
GAME STB
WI-FI HDMI
RS232 serial connector
AV BD PVR CD SAT PVR
WI-FI HEIGHT2 BLUETOOTH HEIGHT1 Z2 OUT LINE OUT STB
FM/DAB
L
TRIG Z1 Z1 IR
R
RS232
ANALOGUE AUDIO
BD CD
CH13/14 CH15/16
TRIG Z2 Z2 IR L
SPEAKER OUTPUTS
SUB2
ZONE2 L
8Ω LOAD IMPEDANCE RECOMMENDED
R
HEIGHT1 L
SR FR C FL SL
SBL
The connector is used with control devices having an RS232
PREAMP OUT
serial port (for example, Crestron and AMX touch-screen
PREAMP OUT
controllers).
FL SL C SBL
Network connector
SBL
SR FR C FL SL
HEIGHT1 L
SUB1 SBR
Networking is a large subject and only the briefest guidelines FR SR
ZONE2 L
are presented in this handbook. Please contact your JBL
CAMBRIDGE, CB25 9PB, UK
DESIGNED IN THE UK
Synthesis dealer or specialist installer for more information
MADE IN VIETNAM
about introducing the Receiver into your computer network.
ETHERNET
OUTPUT1
eARC
USB 5V/0.5A
WI-FI
HEIGHT2 HEIGHT1 Z2 OUT LINE OUT STB GAME AV
L
Ethernet
R
If an Ethernet cable is connected, the Receiver will
ANALOGUE AUDIO
CH13/14 CH15/16
automatically attempt to connect to your network.
L
SUB2
You should use a CAT5 or above cable plugged into the RJ45
ZONE2 R
R
HEIGHT1 R
SR
socket labelled on the rear panel.
SBR
PREAMP OUT
If your network uses static IP addressing rather than DHCP,
PREAMP OUT
you will need to provide an IP address, gateway and DNS
FL SL
C SBL
address; see page EN-34 for information on setting up the
network.
SBR
SR
FR SR SUB1 SBR HEIGHT1 R
USB connector ZONE2 R
The Receiver can be updated via the USB port on the rear of
the unit, if no network connection is available for an "Over
the air" update.
OUTPUT1 ZONE2
BD SAT AV GAME STB
OUTPUT2 PVR UHD
Trigger connectors
eARC OUT
WI-FI
DIGITAL AUDIO
GAME AV BD PVR TRIG Z1 CD Z1 IR
FM/DAB
RS232
TRIG Z2 Z2 IR
STB ANALOGUE AUDIO AV OUT
SPEAKER OUTPUTS
ZONE2 R ZONE2 L
8Ω LOAD IMPEDANCE RECOMMENDED
HEIGHT1 R HEIGHT1 L
SR FR C FL SL
SBR SBL
The trigger connectors (
electrical signal whenever the Receiver is switched on and
the relevant zone enabled.
SBL
SBR
SR FR The trigger signal can be used to switch on and off C FL SL
HEIGHT1 L
HEIGHT1 R
CAMBRIDGE, CB25 9PB, UK
ZONE2 L
ZONE2 R
DESIGNED IN THE UK
compatible pieces of home entertainment equipment, for
example, you could set up a trigger to turn on your television
and BD player whenever the Receiver was switched on.
There are two trigger output sockets on the Receiver, each
capable of outputting a 12V, 70mA switching signal. The
ZONE2
OUTPUT2 PVR UHD BD
OUT
socket is designed for mono 3.5mm jacks: tip is the trigger
output, sleeve is ground.
HDMI
DIGITAL AUDIO
BD PVR CD SAT PVR
FM/DAB
TRIG Z1
Use for remotely turning on and off power amps or source
equipment for Zone 1. On = 12V, Off = 0V.
BD CD STB
SPEAKER OUTPUTS
TRIG Z2
ZONE2 L
8Ω LOAD IMPEDANCE RECOMMENDED
HEIGHT1 L
FR C FL SL
Use for remotely turning on and off power amps or source
SBL
equipment for Zone 2. On = 12V, Off = 0V.
SBL
C FL SL
FR
HEIGHT1 L
ZONE2 L
BD SAT AV GAME STB
Infrared (IR) connectors
BLUETOOTH
HDMI
DIGITAL AUDIO
SAT PVR
TRIG Z1 Z1 IR
tip: Trigger output
RS232
sleeve: Ground
TRIG Z2 Z2 IR
BD CD STB AV OUT
and ) provide an
The infrared inputs (
external IR receivers, either when the Receiver front panel IR
receiver is fully or partially obstructed or to allow the use of a
remote control in Zone 2.
MADE IN VIETNAM There are two IR inputs on the Receiver, each designed for
stereo or mono 3.5mm jacks. Tip is the modulated signal,
sleeve is ground.
Z1 IR
SAT AV GAME STB
This input is intended for use with a local IR receiver when
the front panel of the Receiver is blocked.
WI-FI BLUETOOTH
TRIG Z1 Z1 IR
Z2 IR
RS232
This input is intended for use with an IR receiver in Zone 2 to
allow remote control of Receiver from a second room.
TRIG Z2 Z2 IR
AV OUT
CAMBRIDGE, CB25 9PB, UK
DESIGNED IN THE UK
MADE IN VIETNAM
EN-14
A supplier of infra-red receivers and emitter accessories
and systems is Xantech. See www.xantech.com for more
WI-FI BLUETOOTH
information, or ask your JBL Synthesis dealer.
tip: Modulated signal
NOTE: The IR inputs on the Receiver are designed
sleeve: Ground
for modulated signals. If the external IR receiver
demodulates the IR signal, it will not work. Also the
unit does not provide power for external receivers on
the IR jack, therefore an external power source will
be required.
NOTE: Sockets referring to 'Z2' relate to connections
used in multi-room installation. For more information
and ) allow the connection of
on these connectors, see page EN-11.
CAMBRIDGE, CB25 9PB, UK
DESIGNED IN THE UK
MADE IN VIETNAM