Technical Data; Before Starting The Equipment - EINHELL TE-CI 18/1 Li Manual De Instrucciones

Ocultar thumbs Ver también para TE-CI 18/1 Li:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

4. Technical data

Motor power supply: ............................18 V
Rotational speed at idle: ........ 0-2300 RPM (min
Blow rate: ............................... 0-2900 IPM (min
Clockwise/counter-clockwise rotation: ...........Yes
Bit mount: ...................................... ¼'' (6.35 mm)
Weight: ......................................... 3.1 lbs (1.4 kg)
Max. screw diameter: ..........................
The maximum screw diameter indicates the
maximum diameter of the screw that can be
screwed into wood. The screw diameter can vary
depending on the type of wood.
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
Use only equipment that is in perfect
condition.
Maintain and clean the equipment regularly.
Adapt your way of working to the equipment.
Do not overload the equipment.
Have the equipment checked if necessary.
Switch off the equipment when not in use.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's con-struction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).
Anl_TE_CI_18_1_Li_SPK7_USA.indb 11
Anl_TE_CI_18_1_Li_SPK7_USA.indb 11
EN
Caution:
The metal gear head can become hot during
extended operation.
)
-1
)
-1

5. Before starting the equipment

Please read the following information before you
start using the cordless impact driver for the fi rst
'' (8 mm)
5
time.
16
1. Charge the battery pack with the charger
(battery and charger not included in
4510060).
2. Only use screwdriver bits that are suitable for
the task and in perfect condition.
3. Before screwing into in walls and masonry,
check for concealed electric wiring, gas pipes
and water pipes.
6. Operation
6.1 Charging the Lithium-Ion battery
(not included in 4510060)
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.2 Changeover switch (Fig. 2 / item 3)
The sliding switch above the On/Off switch
is for setting the direction of rotation of the
cordless impact driver and for preventing the
cordless impact driver from being switched on
inadvertently. You can select between clockwise
and counter-clockwise rotation. To avoid causing
damage to the gearing, the direction of rotation
must only be changed when the equipment is at
a standstill. When the slide switch is in the middle
position, the On/Off switch is blocked.
6.3 On/Off switch (Fig. 2 / item 4)
Infi nitely variable speed control is possible with
the On/Off switch. The further you pull the switch,
the higher the speed of the cordless impact driver.
Switching on:
Press the On/Off switch (4).
Switching off :
Release the ON/OFF switch (4).
- 11 -
28.04.2022 15:23:40
28.04.2022 15:23:40

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

45100604510063

Tabla de contenido