Publicidad
Idiomas disponibles
Idiomas disponibles
Instruction Manual
GB
Time switch
Connection diagram
3. Technical data
Supply voltage
230 V, 50-60 Hz
Power consumption
0,2-1,0 W (depending on the switching status)
Contact material
AgSnO2
Type of protection
IP 20 to DIN EN 60529
Permitted ambiet temperature
-30°...+55°
Mode of oeration
1 BSTU
Degree of contamination
2
Rated surge voltage
4 kV
Standard
DIN EN 60730-1/DIN EN 60730-2-7
CFL, LED
Ideal for modern lamps
7. Menu overview
OK
OK
OK
**At 2 channel
version
9. New Program
OK
OK
OK
OK
OK
OK
**At 2 channel
version
Automatic Mode
10. Key function
1. To access the Enter-mode (program, adjustments, options) from the automatic-mode.
2. To revert to the beginning of the current (sub-) menu.
1. To adjust the flashing digit.
2. To scroll through a choice
1. Automatic-mode: To switch the channel ON or OFF until the next programming step occurs.
2. Automatic-mode: A push longer than 3 sec. = Permanent switching status.
/
1. To activate the time switch when operated without power supply.
2. To confirm the selection or the entered data.
13. Additional adjustments
Menu
Main menu
Application
Program
Program
To query the programming steps and remaining memory locations
query
Deletion of switching time(s). The program for all channels, single
Program
Program
channels and single programming steps within on channel can be
delete
deleted.
Date-Time
Adjustment
Adjustment of date and time
Summertime
Adjustment of the daylight saving time mode (ON/OFF)
Adjustment
Language
Adjustment
Choice of languages
Factory
Adjustment
Reset to the state of delivery.
Defaults
Displays the hour counter and pulse counter for each channel and
Counter
Options
the time switch itself.
The time switch can be locked with a 4-digit PIN-Code. The code
PIN-Code
Options
can be adjusted, activated and deactivated. If you have forgotten
the Code please call customer service.
Extra switching time:
Program -> new program -> channel A/B -> Extra switching time -> ...
These programming steps are single switching times by date.
4. Service
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
erm
1. Safety instructions
The installation and assembly of electrical equipment must be
!
only carried out only by a skilled Person! Otherwise fire
danger or danger of an electric shock exists!
Connect the supply voltage/frequency as stated on the
!
product label!
Warranty void if housing opened by unauthorised person!
!
The electronic circuit is protected against a wide range of
!
external influences. Incorrect operating may occur if external
influences exceed certain limits!
5. Intended use
The device fits for the particular use of the following tasks: Illumination
of private and industrial areas, street and shop-window lightening,
regulation of air conditioning, flushing, motors, pumps, plants and
machinery as well as to simulate presence etc.
Operate the device in a dry room only! The installation must be in
accordance with the instruction manual. The device is not qualified for
security relevant tasks such as emergency doors, fire protection
equipment
8. Symbol legend
Channel is switched ON
Channel is switched OFF
For the current date the "holiday program" / "permanent by date" is activated
erm
OK
OK
Standard programming step
Current state is based on a manual over-ride. The state will be cancelled with the next programming step.
Current state is based on a manual over-ride. The state is permanent until terminated manuall.
erm
Days of the week Monday, Tuesday, ... Sunday;
The underscores indicate if the program is active for the days above.
I
Current state is based on a switching time with pulse function
The time switch is locked; to unlock the device the PIN has to be entered.
OK
OK
OK
OK
OK
OK
11. Handling advice
The time switch is programmable without external power supply after pressing the
-button.
To revert one step or one level back while in the Enter-Mode press
After completion of a (sub-) menu confirming
automatic-mode.
end
With
the choice changes from
time switch returns to the beginning of the current
(sub-) menu.
end
When confirming
before completion, the time switch returns to the automatic-
mode without saving the entered data.
14. Pulse
Program -> New program -> Channel A/B -> ...
The pulse function provides you the opportunity of programming a switching time with a defined duration.
As soon as the pulse-duration has expired the time switch switches OFF automatically (the duration of the pulse is up to 59:59 mm:ss).
The programming is carried out like a standard switching time (see point 8 / 9) with following differences
Pulse
Choose
function (9F).
pulstime minute
Define the duration of the pulse (
Program the days of the week
time hour
Program the switching time (
Validation: Confirm the blinking summary of the pulse program
15. Programming via NFC
2. Initial operation
The time switch is delivered in sleep-mode, the display is switched off.
Press
-/
button to wake it up.
The current date and time is already programmed and European daylight
savings time is activated.
Select the desired language by pressing
pressing
. (Remark: By pressing
from the current position)
If required, date, time and daylight savings time mode can be adjusted
also by pressing
-buttons and a subsequent confirmation with
6. Battery
DIN-rail mounting product:
OK
OK
OK
OK
OK
OK
12. Permanent / Extra switching times
/
.
end
will return the device into the
continue
continue
to
. By confirming
the
pulstime second
/
).
time minute
/
)
BA SC18x0 1704x0easy N; ES, GB, PT, FR –23761- 2017.05V02
-buttons and confirm it by
you move one step backwards
.
OK
OK
OK
Permanent On / Off
Extra switching times
optionally selectable
Publicidad
