Technical Data; Noise/Vibration Information - Bosch GWS 18V-180 PC Professional Manual Original

10 | English
a)
(19) Abrasive disc
a)
(20) Cup brush
a)
(21) Round nut
(22) Two-pin spanner for clamping nut/round nut
a)
(23) Open-ended spanner
(24) Handle (insulated gripping surface)
a)
(25) Diamond cutting disc
(26) Disc brush (dia. 22.22 mm)
a)
(27) Disc brush (M14)
a)
(28) Conical brush
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical Data

Angle Grinder
Article number
Rated voltage
A)
Rated speed min
Max. grinding disc dia-
meter/rubber sanding pad
diameter
Grinding spindle thread
Max. thread length of grind-
ing spindle
Kickback control
Soft start
Restart protection
Run-out brake
Weight according to EPTA-
B)
Procedure 01:2014
Recommended ambient
temperature during char-
ging
Permitted ambient temper-
C)
ature during operation
and during storage
Compatible rechargeable
batteries
Recommended re-
chargeable batteries for
maximum performance
Recommended chargers
Data transfer
D)
Bluetooth®
Signal interval
1 609 92A 7AU | (05.08.2022)
a)
a)
GWS 18V-180 PC
3 601 JH6 E..
V= 18
-1
7000
mm 180
M 14
mm 22
●
●
●
●
kg 2.9 – 4.2
°C 0 to +35
°C –20 to +50
GBA 18V...
ProCORE18V...
ProCORE18V...
≥ 5.5 Ah
GAL 18...
GAX 18...
GAL 36...
Bluetooth®4.2
(Low Energy)
s 8
Angle Grinder
E)
Max. signal range
A) Rated no-load speed for the selection of appropriate application
tools in accordance with EN 60745-2-3.The actual no-load
speed is lower for safety reasons and according to production
tolerances.
B) Depends on rechargeable battery (5) and protective
guard ((10), (11)) in use
C) Limited performance at temperatures < 0 °C
D) The mobile devices must be compatible with Bluetooth
ergy devices (version 4.2) and support the Generic Access Pro-
file (GAP).
E) The signal range may vary greatly depending on external condi-
tions, including the receiving device used. The Bluetooth® range
may be significantly weaker inside closed rooms and through
metallic barriers (e.g. walls, shelving units, cases, etc.).

Noise/Vibration Information

Noise emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise level of the power tool are: 83
dB(A); sound power level 94 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-3:
Surface grinding (roughing):
2 2
a = 5.5 m/s , K = 1.5 m/s ,
h
Disc sanding:
2 2
a < 2.5 m/s , K = 1.5 m/s .
h
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
Kickback control
If there is a sudden kickback in the power tool,
e.g. jamming in a separating cut, the power
supply to the motor will be interrupted elec-
tronically.
To restart the tool, set the On/Off switch (8) to the "off" po-
sition and then switch the power tool on again.
GWS 18V-180 PC
m 30
®
Low En-
Bosch Power Tools