Moni Toys KEEP RIDING Instrucciones De Uso página 7

4.The assembly and installation should be performed by an adult. The product contains small or sharp and protruding
parts.
5.Warning! During assembly children under 6 months should not be present. Choking hazard! Small parts.
6.The batteries must be handled by an adult only.
7.Not to be used in traffic.
8.Not to be used on steep slopes or near stairs, near swimming pools or other water bodies. Use the product only on even
grounds and safe areas.
9.Do not allow another child to push the ride-on car while your child uses it.
10.Check regularly the condition of each part. In case of damage there is a risk of injuring your child.
11.Check regularly whether the nut and bolt on the steering wheel are fixed tightly and do not represent any danger.
12.If the product is not assembled properly this may lead to danger.
13.Do not allow the child to use the ride – on car barefoot.
14.The toy complies with Standard EN71 and meets the essential requirements for "General safety of the product".
15.Risk of suffocation. Remove all plastic packing immediately after unpacking the product.
III. HANDLING OF THE BATTERY
1. The battery should be handled by an adult only. Do not allow the children to play with the batteries.
2.Always remove the discharged batteries and do not throw them away with the household waste, use the places
designated for that purpose. They are recyclable.
3. Use АА 1.5V batteries only.
4. Alkaline batteries are recommended.
5. Always remove the batteries, if you will not use the product for a long period of time.
6. When you replace the batteries always replace them with new ones, always replace all batteries. Children should not
be present while you are replacing the batteries.
7. Do not mix old batteries with new ones.
8. Do not mix alkaline, standard (Carbon - Zinc), or rechargeable (Nickel – Cadmium) batteries.
9. Do not throw the batteries in fire, because they may blow up or leak.
IV. CLEANING AND MAINTENANCE OF THE PRODUCT
❖ CLEANING:
1.Regularly clean the product.
2. Do not use corrosive power cleaning agents or cleaning agents on alcoholic base and those, containing abrasive
particles.
3. Clean with soft wet cloth. Always dry with dry soft cloth after this.
❖ MAINTENANCE AND STORAGING:
1. Regularly check the product for broken or damaged parts. If you find any, do not use the product, until you remove the
damage.
2. In case of damage, please contact the trade agent, which you bought the product from or the importer.
3. Do not repair by yourself! Do not make any modifications or changes over the product! This can threaten your child's
health.
4. Regularly check whether the main parts of the car are in good condition (steering wheel, main corpse and wheels).
5.Keep the product from prolong exposure on sunlight, as also from heating sources.
6. Storage on dry and windy place, away from direct heating sources – open fires, cooking ovens and heating appliances.
V. PARTS OF THE PRODUCT
On the table on page 1 are shown the following parts of the product: W – front and rear plastic wheels; CB – car body; VS
– steering column; RB – rear support for the axle; B – backrest; SW – steering wheel; WC – wheel cover; A – front and rear
axle; SF – package with bushings, screws, washers and cotter pins.
VI.INSTRUCTIONS FOR ASSEMBLING OF THE PRODUCT
•Carefully read the instructions before starting to assemble the product.
•Follow exactly the separate steps of assembling and check after each action whether you have fixed the separate parts
well.
•The schemes in this manual are only illustrative. The manufacturer keeps his right to change the way of assembling the
product, without to notifying the customer in advance.
1.Step 1 – Attaching the rear and front wheels – See Figures 1, 2, 3 and 4: Slide the front fork through the opening in 1 of
the wheels. Then attach a bushing to the axle. Slide the axle through the steering column. Attach a bushing to the axle,
then the second front wheel and a washer. Fix the wheel with a cotter pin. Then fix the rear support to the car body. Slide
the rear axle through one of the rear wheels and attach a bushing to the axle. Then slide the axle to the rear support.
Attach a bushing to the other end of the rear axle, the second rear wheel and a washer. Fix with cotter pin.
❖Note: The wheels may be separated each in 2 part – front and rear. Attach them to the each other before attaching the
wheels to the axles.
6