Assembly And Adjustments - Bostitch BTEC25200 Traducido De Las Instrucciones Originales

English

WARNING: RISK OF UNSAFE OPERATION
What can happen
Unsafe op er a tion of your air unit
could lead to se ri ous in ju ry or
death to you or others.

WARNING: RISK OF FALLING
What can happen
A portable unit can fall from a
table, workbench, or roof causing
damage to the unit and could
result in serious injury or death to
the operator.
Specifications
Model
Bore
Stroke
Voltage/Hz-Single Phase
Minimum Branch Circuit Requirement
Fuse Type
Air Tank Capacity
Approximate Cut-in Pressure
Approximate Cut-out Pressure
SCFM @ 90 psig
Regulated Pressure Rating (Approximate)
Quick Connect Type
Duty Cycle
*Tested per ISO 1217
Refer to Glossary for abbreviations.
4
how to prevent it
Review and understand all
instructions and warnings in
this manual.
Be come fa mil iar with the op eration
and con trols of the air unit.
Keep operating area clear of all
persons, pets, and obstacles.
Keep chil dren away from the air
unit at all times.
Do not operate the product when
fatigued or under the influence
of alcohol or drugs. Stay alert at
all times.
Never defeat the safety fea tures of
this prod uct.
Equip area of operation with a
fire extinguisher.
Do not op er ate machine
with missing, broken, or
un authorized parts.
Never stand on the unit.
how to prevent it
Always operate unit in a stable
secure position to prevent
accidental movement of the
unit. Never operate unit on a
roof or other elevated position.
Use additional air hose to reach
high locations.
BTEC25200
1.875" (47.6 mm)
1.592" (40.4 mm)
120/60
15 amps
Time Delay
2.5 gallons (9.4 liters)
165 psig
200 psig
3.0 *
3–150 psi
1/4" (6.4 mm) Industrial
5 minutes on/5 minutes off
Glossary
Become familiar with these terms before operating the unit.
CFM: Cubic feet per minute.
sCFM: Standard cubic feet per minute; a unit of measure of
air delivery.
Psig: Pounds per square inch gauge; a unit of measure
of pressure.
Code Certification: Products that bear one or more of
the following marks: UL®, CUL, CULUS, ETL®, CETL, CETLUS,
have been evaluated by OSHA certified independent safety
laboratories and meet the applicable Standards for Safety.
Cut-in Pressure: While the motor is off, air tank pressure
drops as you continue to use your accessory. When the
tank pressure drops to a certain lower level the motor will
restart automatically. The low pressure at which the motor
automatically restarts is called "cut-in" pressure.
Cut-Out Pressure: When an air compressor is turned on
and begins to run, air pressure in the air tank begins to
build. It builds to a certain high pressure before the motor
automatically shuts off, protecting your air tank from
pressure higher than its capacity. The high pressure at which
the motor shuts off is called "cut-out" pressure.
Branch Circuit: Circuit carrying electricity from electrical
panel to outlet.
Duty Cycle: For proper operation of your air compressor, it
is recommended that a 50% duty cycle be maintained; that
is, the air compressor should not run more than 5 minutes
in any 10 minute period.

ASSEMBLY AND ADJUSTMENTS


WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start-up can cause injury.

WARNING: Risk of unsafe operation. Unit
cycles automatically when power is on.
When performing maintenance, you may be
exposed to voltage sources, compressed air,
or moving parts. Personal injuries can occur.
Before performing any maintenance or repair,
disconnect power source from the compressor
and bleed off all air pressure.
UNPACKING
Remove unit from carton and discard all packaging.
INSTALLATION
How To Set Up Your Unit
Location of the Air Compressor
• Locate the air compressor in a clean, dry and well
ventilated area.
• The air compressor should be located at least 12"
(30.5 cm) away from the wall or other obstructions that
will interfere with the flow of air.