Cleaning And Maintenance; Before First Use; Operating The Appliance; Additional Features - Morphy Richards ELIPTA Instrucciones

44872MEE Rev1_9225 47507 MEE pump - Jon 21/03/2011 15:29 Page 3
g
Features
⁄ Bread slots
Bread carriage lever (with high lift feature)
¤
Cancel button
‹
› Frozen button
fi Reheat button
fl Variable browning control
‡ Removable crumb tray (at rear)
Cord storage
·
Key
Cancel button
Frozen button
Reheat button

BEFORE FIRST USE

• Before using the toaster for the first time, operate the toaster
without bread.
• As with all new electric heating elements, your toaster emits a
'new' smell when it is first switched on. This is quite normal and
not a cause for concern.
OPERATINGTHE APPLIANCE
1 Select the desired level of browning on the browning control dial
.
fl
2 After selecting the desired level, place your bread in the slots
and depress the bread carriage lever
locks.
3 After the set time has been reached, the bread will pop up
automatically - ready for removal from the slots. The bread
carriage lever will have returned to it's upper position and the
heating element will have switched off.
WARNING: Do not wrap the cable around the main body of
the appliance during or after use.

ADDITIONAL FEATURES

Using the cancel button
If you wish to interrupt the toasting process, press the cancel
button .
‹
Using the frozen button
To toast frozen bread, do not adjust the browning control from
your normal setting. Place the bread in the bread slots as normal,
depress the bread carriage lever and press the frozen button
immediately. The button will illuminate and the toaster will operate
for a longer period defrosting and toasting the bread.
1
2
•
•
•
•
⁄
¤ downwards until it
•
•
•
•
•
•
•
›
Using the
re-heat button
If your toast has popped up and gone cold, the toaster offers a
re-heat facility. To use, depress the bread carriage lever and press
the re-heat button fi immediately. The button will illuminate and
the toaster will operate for a short period re-heating the bread.
Crumb tray
A
WARNING: Crumbs will accumulate in the crumb tray and
could catch fire if not emptied regularly.
When the appliance has cooled down completely, tap the sides of
the case lightly to dislodge any crumbs lodged in the appliance
chamber and push the crumb tray
‡
unit. Empty the tray and replace it.
Never operate the appliance without the crumb tray fitted.

CLEANING AND MAINTENANCE

After use and before cleaning, switch off at the mains, remove the
plug from the wall socket and wait for the toaster to cool.
Wipe the outside of the toaster with a damp cloth only and dry
with another cloth or tissue.
NEVER use metal polish or coarse scouring agents and never
immerse your appliance in any sort of liquid.
NEVER use any pointed or sharp articles for cleaning the inside,
otherwise the heating element will be damaged.
NEVER use a brush or push your fingers or metal objects down
the slots.
Hints and tips
In order to achieve uniform browning, we recommend you wait a
minimum of 30 seconds between each toasting, so that the
control can be automatically reset.
If toasting one slice only, you may need to adjust the browning
control to a slightly lower setting.
Please note: you will also notice a slight variation in toast colour
on one side of a single slice.
Stale bread toasts more rapidly than fresh bread. Therefore, the
browning control should be set at a lower setting than usual.
All sorts of bread can be used, as well as teacakes, small rolls
etc. However, slices should not be so thick as to cause burning or
jamming within the bread slots.
If the bread in your toaster becomes jammed, disconnect your
toaster at the socket, allow it to cool, then remove the bread.
When toasting 2 slices, it is recommended they are of equal size
and freshness.
Allow the toaster to cool fully before putting away.
to release from the main
g
3