Simpson SSTP71007 Guia De Inicio Rapido página 2

Ocultar thumbs Ver también para SSTP71007:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

RAPID RETRACTION
Rapid retraction (also known as kickback) of the
engine recoil starter cord will pull your hand and
arm towards the engine faster than you can let go
of the handle resulting in sprains, broken bones,
lacerations, and/or traumatic amputations. Kickback
is caused by damage to the engine crankshaft key,
compression release failure, and/or improper starting
techniques. To avoid kickback follow the appropriate
maintenance schedule and starting instructions listed
in the owner's manual and have engine repair work
done by an authorized service center.
HOT SURFACES
A running engine produces heat. The surfaces of
the engine, other related components, and engine
exhaust gas get hot enough to cause mild moderate
burns or ignite materials on contact. To avoid burns,
do not touch engine surfaces or exhaust gases while
operating and allow engine to cool completely before
moving, touching, or performing any maintenance.
To avoid a fire, keep all flammable materials at least
five feet away from all sides of the product.
HOT OIL
Hot oil can cause serious burns. To prevent getting
burned when changing or checking the engine oil,
use gloves to prevent hot oil from touching skin and
change oil when the engine is warm from but not hot.
FUEL TANK
PRESSURE
Gasoline vapor can build up inside the fuel tank
creating pressure. This pressure may increase when
the engine is hot from running. Opening the fuel tank
under pressure can cause rapid escape of flammable
vapors and possible fuel spills that may ignite from
contact with hot engine surfaces resulting in burn
hazard. To avoid these hazards, always allow the
engine to cool for at least 2 minutes before removing
fuel cap and loosen the fuel cap slowly to relieve any
pressure in the tank.
GASOLINE ADDITIVES
The use of fuel system cleaning additives can
damage the engine and fuel systems. Damage
caused by the use of fuel system cleaning additives
is not covered by warranty. To avoid engine and fuel
system damage, do not use any fuel system cleaning
additives.
Unpacking:
1. Place the shipping carton on a solid, flat surface.
2. Carefully cut the top of the carton open.
3. Carefully cut each corner of the carton from top to bottom.
4. Lay each side of the carton flat on the ground.
5. Remove everything from the carton.
Page 2 of 3
The low oil sensor (if equipped) will automatically
stop the engine when the oil level falls below the safe
limit. To avoid an unexpected shutdown, check the
oil level regularly, fill to the upper limit, and always
operate engine on a level surface.
The engine is shipped from the factory without oil.
Running the engine without oil will result in severe
engine damage and void the warranty. To avoid
causing engine damage and voiding the warranty, fill
the engine with the recommended oil type.
Oil is a major factor in the performance and service
life of any engine. Using the incorrect oil may damage
the engine and void the warranty. To avoid causing
engine damage and voiding the warranty, check and
change oil as required using the correct engine oil.
This pump will not prime when dry. Running the pump
dry without priming can damage the pump assembly
and seals. Damage caused by running dry is not
covered under the warranty. To avoid damaging the
seals and pump assembly, do not run the pump when
it is dry without priming.
Old gasoline can create deposits that clog fuel
systems causing hard starting and poor performance.
Damage caused by old fuel is not covered by
warranty. To minimize deposits, avoid old fuel related
performance issues, and prevent costly repair work,
do not use gasoline that is older than 30 days.
Using gasoline with an alcohol blend greater than
10% (E10) will damage the engine. Damage caused
by using an alcohol blend of 15% (E15), 85% (E85),
or any other alcohol blend higher than 10% (E10)
is not covered under warranty. To avoid engine
damage caused by an alcohol blend that is too high,
use gasoline with 10% (E10) alcohol or lower.
Copyright 2022. All Rights Reserved.
LOW OIL SENSOR
Failure to prime the pump before use can damage the
pump assembly and seals. The pump will not prime
when dry. Damage caused by failing to prime the
pump is not covered by the warranty. Always prime
the pump by pouring water into the primer funnel
until the pump is filled before starting the engine.
FILL ENGINE OIL
BEFORE USING
Operating the engine with a high-altitude carburetor
jet kit at an altitude below 5000 feet (1524 meters)
will cause the engine to run too hot. Overheating the
engine could result in serious engine damage. To
avoid this hazard, make sure the correct carburetor
kit is installed and the air/fuel mixture is set correctly
for your altitude.
USE CORRECT
ENGINE OIL
Water can damage the trash pump engine
components if allowed to enter through cooling slots
or other holes. Damage caused by water intrusion is
not covered under warranty. To avoid engine water
damage, do not use a pressure washer, garden
hose, or any other sources of running water to clean
the trash pump engine, and never submerge the
PUMP DAMAGE
trash pump engine in any liquids.
It is important to prevent gum deposits from forming
in essential fuel system parts, such as the carburetor,
fuel filter, fuel hose or tank during storage. Alcohol-
blended fuels (also called gasohol, ethanol, or
methanol) attract moisture, which leads to separation
OLD GASOLINE
and formation of acids during storage. Acidic fuel and
gum deposits can damage the engine's fuel system
while in storage. Damage caused by the use of old,
stale, or contaminated fuel are not covered under
warranty.
ALCOHOL BLENDS
Overfilling the fuel tank can result in carbon canister
damage (if equipped), poor engine performance, and
void the warranty. To avoid these hazards, do not fill
the fuel tank above the maximum level.
Part Number 7117648 / English
PUMP PRIMING
ALTITUDE
CLEANING
GASOLINE STORAGE
DO NOT OVERFILL
FUEL TANK
REV 3 - 4/21/2022

Publicidad

Tabla de contenido
loading

Productos relacionados para Simpson SSTP71007

Este manual también es adecuado para:

Stp71010

Tabla de contenido