HIKOKI NR 3675DD Instrucciones De Manejo página 19

(3) Pull the nail feeder (A) back to engage the feeder knob to
the nail strip. (See Fig. 10)
NOTE
○ Quietly push the nail feeder (A) and feeder knob against
the nail.
If the nail feeder (A) and feeder knob are released from
backward the magazine and bumped against the nail,
the connecting plastic of the nail can be damaged.
○ Use nail strip of more than 8 nails.
○ Use an unbroken nail strip with nails of all the same
length.
The Nailer is now ready to operate.
Removing the nails:
Pull the feeder knob backward. (See Fig. 11)
Return the feeder knob forward quietly while pushing the
nail feeder (A).
Pull out nails from the back of the magazine. (See
Fig. 12)
HOW TO USE THE NAILER
WARNING
○ NEVER point tool at yourself or others in work area.
○ Keep fi ngers AWAY from trigger when not driving nails to
avoid accidental fi ring.
○ Do not use the electrical cord if damaged. Have it
repaired immediately.
○ Choice of triggering method is important.
Please read and understand "1. Nailing procedures"
found below.
○ Before starting work, check the nailing operation
switching device.
This HiKOKI nailer includes a nailing operation switching
device.
Before starting work, make sure that the switching
device is properly set.
If the switching device is not set properly, the nailer will
not operate correctly.
○ Never place your face, hands or feet near fi ring head
when using.
○ Do not drive nails on top of other nails or with Nailer at too
steep of an angle; nails can ricochet and hurt someone.
○ Do not drive nails into thin boards or near corners and
edges of workpiece. Nails can be driven through or away
from workpiece and hit someone.
○ Never drive nails from both sides of a wall at the same
time. Nails can be driven into and through the wall and
hit a person on the opposite side.
○ Never use Nailer which is defective or operating
abnormally.
○ Do not use Nailer as hammer.
○ Remove all remaining fasteners and battery from nailer
when:
1) doing maintenance and inspection;
2) checking proper operation of push lever and trigger;
3) cleaning a jam;
4) it is not in use;
5) leaving work area;
6) moving it to another location; and
7) handing it to another person.
○ Remove battery from Nailer when:
1) loading nails;
2) turning the adjuster.
This HiKOKI nailer is equipped with a nailer operation
switching device.
Use FULL SEQUENTIAL ACTUATION MECHANISM or
CONTACT ACTUATION MECHANISM in accordance with
the work to be performed.
Explanation of the various nailing operations
○ FULL SEQUENTIAL ACTUATION MECHANISM:
First, press the push lever against the wood; next, pull
the trigger to drive the nail.
Follow the same sequence to continue driving nails.
After nailing once, nailing will not be possible again until
remove fi nger from the trigger and lift the tool off the
wood surface completely.
○ CONTACT ACTUATION MECHANISM:
CONTACT ACTUATION can follow two diff erent
sequences, depending on your use.
To drive several nails:
1. Pull the trigger.
2. Press the push lever against the wood to drive the
nail.
3. If the trigger is held back, a nail will be driven each
time the push lever is pressed against the wood.
To drive a single nail:
1. Press the push lever against the wood.
2. Pull the trigger to drive the nail.
3. Remove your fi nger from the trigger and remove the
nailer from the wood.
[Dry-fi re lockout mechanism]
The machine employs a preventive mechanism for
unloaded operation.
The machine enters a state where the push lever cannot
be pushed up. This takes place when the magazine is
not loaded with nails or when the remaining number of
nails becomes less than 6.
CAUTION
Use caution not to throw the push lever tip onto wood
when the push lever cannot be pushed up.
1. Nailing procedures
This Nailer is equipped with the push lever and does not
operate unless the push lever is depressed.
There are two methods of operation to drive nails with
this Nailer.
They are:
1. Intermittent operation (Trigger fi re):
2. Continuous operation (Push lever fi re):
(1) Intermittent operation (Trigger fi re)
Use the FULL SEQUENTIAL ACTUATION MECHANISM
setting. (See Fig. 13)
WARNING
○ For intermittent operation, Set the nailing operation switch
to FULL SEQUENTIAL ACTUATION MECHANISM
(Nailing operation indicator is light in blue.) (i.e. Set to
SINGLE ACTUATION MECHANISM.)
○ To avoid double fi ring or accidental fi ring due to recoil.
1) Set to FULL
MECHANISM.
2) Pull the trigger rapidly and fi rmly.
Set the nailing operation switch to FULL SEQUENTIAL
ACTUATION MECHANISM (Nailing operation indicator
is light in blue.)
(to set to FULL
MECHANISM).
(Set the switching device to the nailing operation
indicator light in blue mode completely as shown in
the Fig. 13. Otherwise, it will be set to CONTACT
ACTUATION MECHANISM.)
Position the nail outlet on the workpiece with fi nger off
the trigger.
Depress the push lever fi rmly until it is completely
depressed.
Pull the trigger to drive a nail.
Remove fi nger from the trigger and lift the tool off the
wood surface completely.
To continue nailing in a separate location, move the nailer
along the wood, repeating steps
NOTE
Operations and
of each other. If more than 2 seconds pass after
Nailer will not work properly. If this happens, retry from
.
19
English
SEQUENTIAL ACTUATION
SEQUENTIAL ACTUATION
- as required.
should be done within 2 seconds
, the