Dispensing Cold Water; Cleaning & Maintenance; Warnings And Safety Precautions - Primo T355 Manual Del Usuario

Deluxe Water Dispenser
OPERATING INSTRUCTIONS

DISPENSING COLD WATER

Water will take approximately 1 hour after initial set up
to become completely chilled.
Press drinking glass or container against
the paddle beneath the blue circle to
dispense cold water. Release to stop
dispensing.
REPLACING THE BOTTLE
Pull upward to remove the empty bottle from the
bottle holder.
Grab a bottle of Primo water and remove the sticker
from the cap.

WARNINGS AND SAFETY PRECAUTIONS

To reduce risk of injury and property damage, user must read this entire guide before
installing and using this dispenser. Failure to execute the instructions in this manual may
result in personal injury or damage to property. When operating this dispenser always
exercise basic safety precautions including the following:
Prior to use this dispenser must be installed in accordance with this manual.
This dispenser is intended for water dispensing only. Do NOT use other liquids. Never
use any liquid in the dispenser other than known and microbiologically safe bottled water.
Do not use if plug or cable are damaged.
Never unplug by pulling power cable, always hold the plug.
To protect against electric shock, do not immerse plug or cable in water or any other
liquid. Do not operate with wet hands.
The water in the bottle on a cooler can be adversely affected by any of the conditions
listed below.
Water coolers should not be located:
In the open air.
In direct sunlight or any area that is brightly lit for long periods (i.e. 24 hours/day).
Inside of, or close to, a lavatory.
In laboratories.
In a dusty, unventilated or excessively humid location.
LIMITED WARRANTY
Eden Springs UK Limited, ("Vendor") warrants to the original purchaser of this dispenser, and to no other person, that if this dispenser is assembled and operated in accordance with the printed instructions accompanying it,
then for a period of one (1) year from the date of purchase (or such other period as agreed by Vendor in writing and/or which may apply in accordance with any extended registered warranty offered by the Vendor from time
to time), all parts in such dispenser shall be free from defects in material and workmanship. Vendor may require reasonable proof of your date of purchase from an authorized retailer or distributor. Therefore, you should
retain your sales slip or invoice. The Limited Warranty shall be limited to repair or replacement of parts which prove defective under normal use and service and which Vendor shall determine in its reasonable discretion upon
examination to be defective. Before returning any parts, you should contact Vendor's Customer Service Department using the contact information listed below. If Vendor confirms, after examination, a defect covered by this
Limited Warranty in any returned part, and if Vendor approves claim, Vendor will replace such defective part without charge. If you return defective parts, transportation charges must be prepaid by you. Vendor will return
replacement parts to original purchaser, freight or postage prepaid. The Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration, misapplication, improper installation
or improper maintenance or service by you or any third party, or failure to perform normal and routine maintenance on the dispenser, as set out in the User's Manual. In addition, the Limited Warranty does not cover damage
to the finish after purchase, including without limitation scratches, dents, discoloration or rust. Vendor disclaims all warranties for products that are purchased from sellers other than authorized retailers or distributors.
EXPRESS WARRANTY DESCRIBED ABOVE, TO THE EXTENT PERMITTED BY LAW, VENDOR DISCLAIMS ANY AND ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FURTHER, VENDOR SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FOR ANY SPECIAL,
INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Vendor assumes no responsibility for any defects caused by third parties.
Primo Water Consumer Services:
Eden Springs UK Ltd, 3 Livingstone Boulevard, Blantyre G72 0BP, United Kingdom.
PRIMO Consumer Services
www.primodispensers.com | UK +44 (0)800 0274747 | EU +34 93 566 5089 | help@primodispensers.com
Consumer Services EU: Write to
Eden Springs, Berbo-Grens Service BV, Marketing 43, NL -6921 RE Duiven. The Netherlands.
Manufactured by: Foshan Shunde Midea Water Dispenser Manufacturing Co., Ltd No.68, Guangle Road, Beijiao Town, Shunde District, Foshan City, Guangdong Province, China.
Made in China
Carefully lift bottle and insert onto probe. Apply slight
pressure if needed to ensure that the cap is fully pierced.
Water will begin to flow into the reservoirs causing air
bubbles to rise in the bottle.
CLEANING & MAINTENANCE
For best taste, performance, and hygiene,
clean your cabinet, controls, bottle probe and
spouts regularly.
Please follow the correct Primo cleaning
instructions for your product.
Visit primodispensers.com for detailed cleaning
instructions.
In front, or within 200mm, of a heating radiator or heating/air conditioning duct.
In a restricted passage or on a fire escape route.
On uneven or sloping surfaces.
On weak floors or shelving.
In areas which are subject to flooding or dampness underfoot.
Where there is difficult access for cooler maintenance or care.
Where there is potential for pest infestation.
In the open (e.g. building sites).
In the following locations in hospitals e.g.:
Intensive care units.
Neonatal units.
Oncology units.
Transplant units.
Surgical wards.
Operating theatres.
A crossed-out wheelie bin symbol denotes that waste
electrical and electronic equipment and batteries must not be
disposed of as unsorted municipal wasted but collected separately.
For more detailed information, please go to www.primodispensers.com/terms
©2021 Copyright Eden Springs UK Ltd