Screwdriver Safety Warnings; Drill Safety Warnings - Gude BSS 18 1/2-0 BL Instrucciones De Uso Originales

ENGLISH
b) Do not expose a battery pack or tool to fire or ex-
cessive temperature. Exposure to fire or temperature
above 130 °C may cause explosion.
c) Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging impro-
perly or at temperatures outside the specified range may
damage the battery and increase the risk of fire.
6)Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.This
will ensure that the safety of the power tool is maintained.

Screwdriver safety warnings

Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring.Fasteners contacting a
„live" wire may make exposed metal parts of the power
tool „live" and could give the operator an electric shock.

Drill safety warnings

Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may con-
tact hidden wiring.Cutting accessory contacting a „live"
wire may make exposed metal parts of the power tool
„live" and could give the operator an electric shock.
Additional Safety and Working
Instructions
Use protective equipment. Always wear safety glasses
when working with the machine. The use of protective
clothing is recommended, such as dust mask, protective
gloves, sturdy non-slip footwear and ear defenders.
The dust produced when using this tool may be harmful
to health. Do not inhale the dust. Use a dust absorpti-
on system and wear a suitable dust protection mask.
Remove deposited dust thoroughly, e.g. with a vacuum
cleaner.
Do not machine any materials that present a danger to
health (e.g. asbestos).
When working in walls ceiling, or floor, take care to
avoid electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclam-
ped workpieces can cause severe injury and damage.
Please turn the device immediately off when the tool
used gets blocked! Do not turn the device on again
when the tool is still blocked. This could cause bounce
back with a high reaction moment. Determine and
remove the cause of the blocking of the tool used while
respecting the safety instructions.
The possible causes may be:
it is tilted in the workpiece to be machined
it has pierced through the material to be machined
the power tool is overloaded
Do not reach into the machine while it is running.Chips
and splinters must not be removed while the machine
18
is running.
WARNING! Danger of burns
The insertion tool may become hot during use.
• when changing tools
• when setting the device down
The appliance must not be used if damaged or safety
equipment is defective. Replace any worn-out and
damaged parts.
Do not use the appliance if you are tired, ill, under influ-
ence of drugs, alcohol drinks or medicaments.
Do not let any metal parts reach the airing slots - dan-
ger of short circuit!
Electronics
In case of overload, the rotational speed is being redu-
ced until machine stops. Please note that the machine
will automatically accelerate back to its original opera-
ting speed if the load is removed from it.
Battery
Risk of fire! Risk of explosion!
Never use damaged, defective or deformed accumu-
lators. Never open or damage the accumulator or let it
fall on the ground.
• Never charge the battery in an environment with
acids and easily flammable materials.
• Protect the battery against heat and fire.
• Battery to be used at the ambient temperatures
between 10°C and +40°C only.
• Never put the battery on heaters and do not expose
it to strong sunlight for a long time.
• After being subject to heavy load, let the battery
cool down first.
Shorting the battery terminals together may cause
burns or a fire.
• Short circuit - do not bridge the accumulator con-
tacts with metal parts.
• When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
• The accumulator must be packaged (plastic bag,
box) or accumulator contacts must be sealed up for
accumulator disposal, transport or storage.
The Güde charger to be used only to charge the battery.
There can be malfunction or fire if different chargers are
used.
Vapours may leak out in case of unauthorised use or
when using a damaged accumulator. Bring fresh air and
seek medical advice if experiencing difficulties. Vapours
may irritate the respiratory system.
Working Instructions Battery
Accumulators are supplied partially charged and must
therefore be fully charged before being used for the