Berner BBC-2 14,4-18V Manual Original página 9

Transportation of those batteries has to be done in accordance with local,
national and international provisions and regulations.
• The user can transport the batteries by road without further requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject to
Dangerous Goods regulations. Transport preparation and transport are
exclusively to be carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to prevent
short circuit.
• Ensure that battery pack is secured against movement within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
CHARACTERISTICS
After inserting the battery into the reception of the charger the battery will
automatically be charged (red control lamp is illuminated continuously)
When a hot or cold battery pack is inserted into the charger (fl ashing red
lamp), charging will begin automatically once the battery reaches the correct
charging temperature (0°C...65°C). The max. charging current is fl owing when
the temperature of the Li-Ion-battery is between 0°C and 65°C.
The battery's charging time is between 1 min and 30 min (at 1,5 Ah),
depending on the state of discharge.
Once the battery is fully charged, the LED on the charger changes from red to
green.
It is not necessary to remove the battery after charging. The battery can be
stored permanently in the charger without the danger of being overcharged.
Under certain circumstances the charger may cause the LED indicators to
fl ash alternately red and green.
If this occurs, Remove the battery and reinsert.
If the LEDs still does not come on, remove pack(s) and unplug charger for at
least 2 minutes. After 2 minutes, plug charger back in and insert pack"
If both LEDs continue to fl ash, take the charger and battery out of use
immediately for safety reason and have them inspected by a Berner customer
service center.
LIGHT INDICATORS
Continuous red
Continuous green
Fast fl ashing red
Slow fl ashing red
Flashing red/green
MAINTENANCE
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualifi ed persons in order to
avoid a hazard.
457 696 - Berner-BBC-2 14-4-18V.indd 9 457 696 - Berner-BBC-2 14-4-18V.indd 9
Charging
Charging is complete
Battery is too hot/cold - Charging will
begin when battery reaches correct
charging temperature
Battery charge is pending - Charging
will begin when the fi rst pack is fully
charged
Damaged or faulty battery pack
Use only Berner accessories and Berner spare parts. Should components
need to be replaced which have not been described, please contact one of our
Berner service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
ten-digit No. as well as the machine type printed on the label and order the
drawing at Berner.
SYMBOLS
Please read the instructions carefully before starting the
machine.
Do not burn used battery packs.
Never charge a damaged battery pack.
Replace with a new one.
Do not dispose electric tools, batteries/rechargeable batteries
together with household waste material.
Electric tools and batteries that have reached the end of their
life must be collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for recycling advice
and collection point.
This tool is only suitable for indoor use. Never expose tool to
rain.
Class II tool.
Time-lag fuse 3.15 A
T3.15A
European Conformity Mark
GUARANTEE AND GUARANTEE SERVICE
Each tool, spare part or accessory is consistently checked before being
dispatched from the manufacturing plant. If, despite this fact, there are any
defects, please send the item directly to our Client Services Headquarters or to
the nearest service repair shop of the firm Berner.
The warranty period of 36 months for tools and 12 months for batteries and
chargers starts on the date of purchase which must be verifi ed using the
original receipt. During the guarantee period the producer guarantees:
• free removal of possible defects;
• free replacement of all damaged parts;
• free professional servicing.
The requirement for this is that the problem is a material and/or manufacturing
fault. Defects or faults caused by incorrect treatment or excessive force are not
covered by the warranty. Furthermore, only original accessory parts may be
used, which Berner has expressly identifi ed as suitable for the operation with
Berner machines.
You can fi nd out the location of your nearest customer service workshop in the
address list at the back of this document.
9 ENGLISH
13.07.2020 10:28:58 13.07.2020 10:28:58