EINHELL TE-CD 18/2 Li-i Manual De Instrucciones página 36

The torque for a specific size of screw is selected
with the set-collar (1). The correct torque depends
on several factors:
•
on the type and hardness of material in ques-
tion
•
on the type and length screws used
•
on the requirements needing to be met by the
screwed joint.
The clutch disengages with a grating sound to
indicate when the set torque is reached.
6.3 Selector switch for driving/drilling/impact
drilling (Fig. 4/Item 11)
•
For driving purposes, set the selector switch
(11) to the „Screw" position. The torque is
adjusted via the torque setting (1) (see point
6.2).
•
For drilling purposes, set the selector switch
(11) to the „Bit" position. The slip coupling is
now off and the maximum torque is available
regardless of the torque setting (1).
•
For impact drilling purposes, set the selector
switch (11) to the „Hammer" position. The slip
coupling is now off and the maximum torque
is available regardless of the torque setting
(1).
Important! Change the torque setting (1) and
the selector switch for driving/drilling/impact
drilling (11) only when the equipment is at a
standstill.
6.4 Forward/Reverse switch (Fig. 5 / Item 3)
With the slide switch above the On/Off switch you
can select the direction of rotation of the battery-
powered drill/screwdriver and secure it against
being switched on accidentally. You can choose
between clockwise and anticlockwise rotation. To
avoid causing damage to the gearing it is advisa-
ble to change the direction of rotation only when
the tool is at a standstill. The On/Off switch is blo-
cked when the slide switch is in centre position.
6.5 On/Off switch (Fig. 5 / Item 4)
Infinitely variable speed control is possible with
the On/Off switch. The further you press the
switch, the higher the speed of the battery-powe-
red drill/screwdriver.
6.6 Changing over from 1st gear to 2nd gear
(Fig. 4 / Item 7)
You can work at a higher or lower speed depen-
ding on the position of the selector switch. To avo-
id damaging the gear unit you should only change
Anl_SA_TE_CD_18_2_Li_i_SPK8.indb 36 Anl_SA_TE_CD_18_2_Li_i_SPK8.indb 36
GB
over gears when the tool has stopped.
6.7 Battery capacity indicator (Fig. 6 – Item 2)
Press the battery capacity indicator switch (a).
The battery capacity indicator (2) shows the char-
ge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack.
6.8 LED lamp (Fig. 6 / Item 10)
The LED lamp (10) can be used in poor lighting
conditions to illuminate the area where you want
to drill or screw. The LED lamp (10) will be lit
automatically as soon as you press the ON/OFF
switch (4).
6.9 Changing the tool (Fig. 7)
Important. Set the changeover switch (3) to its
centre position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the cordless screwdriver.
•
The cordless screwdriver is fitted with a
quick-action chuck (9) with an automatic
spindle stop.
•
Open the chuck (9). The chuck opening (a)
must be large enough to hold the tool (drill bit
or screwdriver bit).
•
Select the suitable tool. Push the tool as far
as possible into the chuck opening (a).
•
Tighten the chuck (9) and then check that the
tool is secure.
6.10 Screwdriving
We recommend using self-centering screws (e.g.
recessed head screws) designed for reliable wor-
king. Be sure to use a bit that matches the screw
in shape and size. Set the torque, as described
elsewhere in these operating instructions, to suit
the size of screw.
- 36 -
05.01.2022 10:43:20 05.01.2022 10:43:20