Cleaning, Maintenance And Ordering Of Spare Parts; Carbon Brushes; Disposal And Recycling - EINHELL TE-MB 18/127 U Li Manual De Instrucciones Original

bandsaw in the top position (see 5.6.2).
•
Clamp the workpiece securely as described
in 5.6.5.
•
Important! After every new adjustment we
recommend you to make a trial cut in order to
check the new settings.
•
Hold the bandsaw firmly by the handle (1) and
release the pushlock button (26) as described
in 5.6.2.
•
Switch on the bandsaw as described in sec-
tion 6.3.
•
Now guide the bandsaw with a firm grip to the
workpiece and cut into it carefully.
•
Do not exert excessive pressure on the blade!
This way you will obtain the straightest pos-
sible cut while also prolonging the life of the
blade.
•
Warning! The blade must have stopped mo-
ving before the workpiece is removed.
6.6 Transport
•
Set the angle on the base frame (24) to 0°
and lock it in place with the clamping lever
(31) (see 5.6.3).
•
Use the pushlock button (26) to lock the
bandsaw in the bottom position (see 5.6.2).
•
Clamp the movable clamping jaw (27) against
the fixed clamping jaw (28) (see 5.6.5).
•
Transport the machine by lifting it only by the
handle (1), the adjustable handle (10) or the
base plate (24).
•
Never use the guards for handling or trans-
porting purposes.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the mo-
tor housing free of dirt and dust as far as pos-
sible. Wipe the equipment with a clean cloth
or blow it with compressed air at low pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use cleaning
agents or solvents; these could attack the
plastic parts of the equipment. Ensure that no
Anl_TE-MB_18_127_U_Li_SPK13.indb 27 Anl_TE-MB_18_127_U_Li_SPK13.indb 27
GB
water can seep into the device. The ingress of
water into an electric tool increases the risk of
an electric shock.

7.2 Carbon brushes

In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Danger! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician.
7.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell-Service.com

8. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should be
taken to a suitable collection center for proper dis-
posal. If you do not know the whereabouts of such
a collection point, you should ask in your local
council offi ces.
9. Storage
Store the equipment and accessories in a dark
and dry place at above freezing temperature. The
ideal storage temperature is between 5 and 30 °C.
Store the electric tool in its original packaging.
Important! We recommend you to slacken the
blade (see 5.5) if you are not going to use the
machine for a long time. We also recommend you
to protect the guide rollers (20) with mineral oil
during long periods of storage.
- 27 -
15.09.2022 11:08:29 15.09.2022 11:08:29