LUND 68193 Manual Original página 12

GB
Fill the kettle with water so that the water level is between the minimum and maximum indicators. Close the kettle lid.
Fully unwrap the base's power cord and plug it into the socket.
Check that the product switch is in the "off " position - O.
Place the kettle on the base so that the kettle rests on the base with its whole circumference.
Turn the kettle on by pressing the switch and moving it to the "on" position - I.
The backlight of the kettle will be visible all the time the water is boiling.
The kettle will switch off automatically once the water is boiled. The switch will automatically change to the "off " position - O, and
the backlight will turn off .
Lift the kettle from the base by grasping by the handle only.
It is not necessary to open the lid for pouring water.
Remove the power supply cord plug from the socket.
Leave the product to cool after use.
Warning! The kettle and lid are very hot when the water is heated. Avoid touching the metal parts of the kettle and the lid. It is
recommended to wear heat-protective gloves.
Caution! Moving the switch to the "off " position - O manually, ends the water-heating process at any time.
Control panel (for models 68194 and 68195 only)
The kettle is equipped with a control panel, which signifi cantly expands the functionality of the product.
The model 68194 has the control panel located in the handle, and 68195, in the product base.
Operation of the panel is carried out by means of buttons, reading is possible by means of the display.
The I/O switch button allows to turn the kettle on and off .
The buttons marked "+" and "-" allow to set the temperature at which water heating will end.
The button marked with the symbol of steam fl oating over the appliance allows to activate the water-temperature maintenance
function.
Model 68194 and 68195
Lift the lid by pressing the button.
Fill the kettle with water so that the water level is between the minimum and maximum indicators. Close the kettle lid.
Fully unwrap the base's power cord and plug it into the socket.
Place the kettle on the base so that the kettle rests on the base with its whole circumference, the display will show the current
water temperature.
Set the water temperature using the buttons marked "+" and "-". The factory pre-set temperature is 100 C. If no other temperature
O
is set before switching on the kettle, the kettle will boil the water.
Turn the kettle on by pressing the switch. Each press of any button is indicated by a sound signal.
The display will show the water temperature at all times when the water is being heated.
The kettle will switch off automatically once the water is heated to the set temperature. The backlight will turn off and a sound
signal will be heard.
Lift the kettle from the base by grasping by the handle only.
It is not necessary to open the lid for pouring water.
Remove the power supply cord plug from the socket.
Leave the product to cool after use.
Warning! The kettle and lid are very hot when the water is heated. Avoid touching the metal parts of the kettle and the lid. It is
recommended to wear heat-protective gloves.
Caution! Pressing the switch manually ends the water-heating process at any time.
Caution! If during water heating the temperature is changed to a lower one or the kettle is lifted from the base, the kettle will
automatically end the water-heating process.
Caution! If the temperature is set lower than the temperature of the water in the kettle, it will not be possible to turn the kettle on.
The kettle does not have a water cooling function.
Due to the thermal inertia of the temperature sensor, a slight discrepancy between the actual water temperature and the display
is possible. The sensor inaccuracy is given in the technical data table.
Water temperature maintenance function (models 68194 and 68195 only)
Setting the water temperature, turning on the heating and then pressing the button marked with the fl oating steam symbol will acti-
vate the water temperature maintenance function. This function allows to heat up the water and then maintain the set temperature.
Activation of the temperature maintenance function is signalled by the backlight of button with the symbol of steam fl oating over
the appliance coming on in the model 68194 or by displaying the symbol of steam fl oating over the appliance in the model 68195.
Caution! Lifting the kettle from the base disables the water temperature maintenance function.
Caution! The water temperature maintenance function can only be activated in the temperature range of 40-95 O C for a maximum
O R I G I N A L I N S T R U C T I O N S
12