EINHELL TC-JS 80/1 Manual De Instrucciones página 16

5.2 Changing the saw blade (Fig. 2/Item 12)
Danger!
•
Pull the mains plug before you fit or replace a
saw blade.
•
Set the selector switch for pendulum action
(8) to position 3. The teeth of the saw blade
are very sharp!
•
Press the blade holder (14) and insert the
saw blade (12) into the blade holder (14) as
far as the stop (Fig. 2). The teeth on the saw
blade must be pointing forwards.
•
Allow the blade holder (14) to slide back to
starting position.
•
The saw blade (12) must sit in the guide roller
(10).Check that the saw blade (12) is secure-
ly mounted in the blade holder.
•
Follow the instructions above in reverse order
to remove the saw blade.
Warning! Hold the saw blade securely while
releasing it because otherwise it may jump
out of the blade holder.
5.3 Setting the soleplate for miter cuts
(Figs. 3-4)
•
Use the hexagon key (4) to loosen the screws
for the soleplate (11) on the bottom of the ad-
justable soleplate (7) (Figure 3).
•
Pull the sole plate (7) backwards slightly. The
soleplate can now be swiveled a maximum
45° to the left and right.
•
If the soleplate (7) is pushed back to the
front again it will only function in the locking
positions at 0°, 15°, 30° and 45°, which are
marked on the graduated scale for the sole-
plate (9) (Figure 4). Move the soleplate into
the required position and refasten the screw
securing the soleplate (11).
•
However, the soleplate (7) is also easily set to
another angle. To do so, move the soleplate
(7) to the rear, set the desired angle and re-
fasten the screw securing the soleplate (11).
5.4 Adapter for dust extraction system
(Figure 5/Item 6)
•
Connect your jigsaw to a vacuum cleaner
using the adaptor for dust extraction (6). This
will provide excellent dust extraction on the
workpiece. The benefits are that you will pro-
tect both the equipment and your own health.
Your work area will also be cleaner and safer.
•
Dust created when working may be dange-
rous. Refer to the section entitled "Safety
instructions".
Anl_TC_JS_80_1_SPK13.indb 16 Anl_TC_JS_80_1_SPK13.indb 16
GB
•
Attach the adaptor (6) as shown in Figure 5,
so that it is securely seated in the housing.
•
Fit the vacuum tube of the vacuum cleaner
onto the adaptor opening (6). Check that the
connections are airtight.
6. Operation
6.1 ON/OFF switch (Fig. 6/Item 3)
To switch on:
Press the ON/OFF switch
To switch off :
Release the ON/OFF switch
6.2 Locking button (Fig. 6/Item 2)
You can lock the ON/OFF switch (3) using the lo-
cking button (2) when the equipment is in operati-
on. To switch off the equipment briefl y hold down
the ON/OFF switch (3).
6.3 Electric speed selector (Fig. 6/Item 1)
You can pre-select the required speed with the
speed selector. Turn the speed selector in PLUS
director to increase the speed and turn the speed
selector in MINUS direction to reduce the speed.
The suitable stroke speed is dependent on the
relevant material and working conditions.
General rules for cutting speeds for metal cutting
work must be complied with here as well.
You can generally use a higher speed with fi ne
saw blades whilst coarser saw blades require
lower speeds.
Position MIN-2 = low stroke speed (for steel)
Position 3-4 = medium stroke speed (for steel,
soft metal, plastic)
Position 5-MAX = high stroke speed (for soft-
wood, hardwood, soft metal, plastic)
6.4 Setting the pendulum action
(Fig. 7/Item 8)
•
The strength of the pendulum action of the
saw blade (12) can be adjusted using the se-
lector switch for pendulum action (8).
•
You can adjust the cutting speed, the cutting
performance and the finish to the workpiece
you wish to saw.
- 16 -
07.04.2022 15:15:18 07.04.2022 15:15:18