Optional Accessories - Makita HR2652 Manual De Instrucciones

Using dust cup set
Optional accessory
Fit the dust cup set against the ceiling when operating
the tool.
► Fig.35
NOTICE:
Do not use the dust cup set when drill-
ing in metal or similar. It may damage the dust
cup set due to the heat produced by small metal
dust or similar.
NOTICE:
Do not install or remove the dust cup
set with the drill bit installed in the tool. It may
damage the dust cup set and cause dust leak.
MAINTENANCE
CAUTION:
Always be sure that the tool is
switched off and unplugged before attempting to
perform inspection or maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
To maintain product SAFETY and RELIABILITY,
repairs, any other maintenance or adjustment should
be performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.
Replacing filter of dust case
1.
Remove the dust case while pressing down the
lever of the dust case.
► Fig.36: 1. Lever
2. Insert a flat-blade screwdriver between the filter
case and the cover of the dust case as shown in the
figure. While pressing and bending the sides of filter
case, lift up the filter case with the flat-blade screwdriver
and remove the filter case.
► Fig.37: 1. Flat-blade screwdriver 2. Filter case
3. Cover of the dust case
3. To remove the filter from the filter case, turn them
upside down and push up the filter as shown in the
figure.
► Fig.38: 1. Filter 2. Filter case
4.
Attach a new filter to the filter case, and then
attach them to the dust case aligning the protrusion on
the filter case with the groove on the dust case.
► Fig.39: 1. Protrusion 2. Groove
5. Close the cover of the dust case, and then attach
it to the tool.
Replacing sealing cap
Optional accessory
Replace a sealing cap at regular intervals as a worn or
damaged sealing cap may affect the suction performance.
1.
Insert a flat-blade screwdriver, with its flat surfaces
vertical, into one of the release holes placed on the sides of
the nozzle head. Tilt the flat-blade screwdriver at an angle to
squeeze and pop the cube hook of the sealing cap out of the
molded receptacle. Then peel the rubber edges of the sealing
cap away from the rims of the nozzle head opening.
► Fig.40: 1. Sealing cap 2. Cube hook 3. Release
hole 4. Nozzle head
2. Set one of cube hooks of a renewed sealing cap
into the molded receptacle in the nozzle head with a
recessed surface of the sealing cap facing forwards.
► Fig.41: 1. Cube hooks 2. Receptacles 3. Sealing
cap 4. Recessed surface
3.
Place the other hook into the receptacle on the
opposite side of the nozzle head, while repositioning the
sealing cap to fit finely to the nozzle head.
► Fig.42: 1. Sealing cap 2. Cube hook 3. Receptacle
4. Nozzle head 5. Rims
4. Gently lay the rubber edges of the sealing cap down
over the rims of the nozzle head opening from bottom to top.
► Fig.43: 1. Rubber edges 2. Sealing cap 3. Nozzle head

OPTIONAL ACCESSORIES

CAUTION:
These accessories or attachments
are recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or attachment
for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• Carbide-tipped drill bits (SDS-Plus carbide-tipped bits)
• Core bit
• Bull point
• Diamond core bit
• Cold chisel
• Scaling chisel
• Grooving chisel
• Chuck adapter
• Keyless drill chuck
• Bit grease
• Depth gauge
• Blow-out bulb
• Dust cup
• Dust cup set
• Safety goggles
• Plastic carrying case
NOTE: Some items in the list may be included in the
tool package as standard accessories. They may
differ from country to country.
14 ENGLISH