Preparing For Installation; Remote Control - Sulion ACHILIA Manual De Instalación

Do not throw away electrical products together
with household waste. We ask you to recycle the
packaging at the collection points provided for this
purpose. Contact local authorities or your provider
for recycling advice. Thank you for recycling at
the collection points provided for this manual.
Device technical spectifications
General
Nominal voltage and frequency
Protection category
Ingress protection
Work temperature
Maximun ceiling slope on which it can be installed
Weight
Power consumption in standby mode (W)
Service value measurement standard
Bulb
Bush
Number of bushes
Wattage
B
Maximum bulb size
A
12
Fan
Speed
Power (W)
RPM
Airflow (m³/min)
Airflow (m³/h)
Max noise level (dB)
Service value SV ((m³ / min) / W)
Maximum air speed (m / sec)
Installing a fan without a shaft, flush with the ceiling, can reduce airflow.
CIF A28763647
Note: The important warnings and instructions indicated in
this manual are not guaranteed to cover all possible conditions
and situations that may occur. It must be understood that
common sense, precaution, and care are factors that cannot
be included in all products. These factors can and must only
be provided by the user who maintains and enjoys this fan.
220-240V~AC 50/60Hz
+34 916774540 Calle Verano, 51 - Polígono Industrial Las Monjas -28850 Torrejón de Ardoz - Madrid (ESPAÑA)

Preparing for installation

Note: The estimated installation time is 120 minutes. This
product can only be installed by a certified electrician Ca-
refully separate the fan's parts, avoiding the use of cutters
or blades that could scratch any part of it.
Remove the fan from the packaging carefully, avoiding the
use of knives which could scratch any part of it.
Remove all the components. Place the motor on a cloth or
wet surface so as not to damage its surface finish. Carefully
handle the unit to make sure that its casing does not bend
or get scratched.
The fan must be mounted on the floor or a large enough
Clase I
table to prevent any component from falling off.
IP20
Instructions for synchronizing the
-5 40ºC
↔
receiver and the remote control
15º
6Kg The control is already factory-linked with its receive.
Make sure all connections are correctly made.
<0,5
Make sure that the remote control contains batteries.
EN 62879:2020
Make sure that all switches (main and isolation) are on.
The control of this fan have two mode of synchronization,
Universal mode and Unit mode:
E27
- Unit Mode:
2
This type of synchronization allows you to control two or
Máx. 2x40W
more nearby fans independently, each with its remote con-
A 60mm
trol.
Synchronization:
B 82mm
The control of this fan does not require synchronization
with the receiver, the control is already factory-linked with
its receiver
6
- Universal Mode:
25
This type of synchronization allows you to control one or
more nearby fans with the same remote control.
230
Synchronization:
140
1.-Connect the power (wall switch) of the fan or fans that
9300
you want to control, and then just within the following
55 15 seconds, press the key
continuous seconds.
5,6
2.-A "beep" sound indicates that the connection has been
2,69m/s
executed and the equipment can function normally.
3.-Now, transmitter and receiver of the fan / s will have
been synchronized. Turn off the fan / s current using the
switch or automatic and then turn it back on / s, this step
is the one that closes the synchronization process.
It is not possible for a controller to forget a fan once it has
been linked, if you want a fan to leave
to obey a command, another one must be linked to
"overwrite it".
ATC: 916749481 - info@sulion.es / SAT : 916749483 - sat@sulion.es

Remote control

Turn on
fan
Turn on
light
Turn off all
Speeds
of the remote control for 10
Turn off
Fan
Turn off
light
Summer
/Winter
Timer
13
www.sulion.es