EWT Optiflame BACH Manual Del Usuario página 4

When planning where to position your purpose built support
structure the following steps must be observed:
1. Place the fire in the desired location to see how it will look
in the room.
2. Mark the desired location for the new support structure in the
room and store the fire in a safe, dry and dust free location.
3. Using timber studs to support the fire, devise and construct
a suitable means of supporting the product within the wall
partition and provide electrical power for the fire to be HARD
wired. For recommended sizes of height, width and depth
of opening for recess and hole fixing dimensions for each
model - see Fig. 1.
4. Remove the front/trim by following the steps as outlined
previously.
5. Locate the 4 fixing holes, position the fire accordingly, and
firmly fix using the appropriate screws.
6. Replace the front/trim.
NOTE: The appliance should be HARD wired to an electrical
power outlet when placed in a recessed installation.
Please consult a qualified electrician for appropriate wiring
requirements.
Controls - see Fig. 2
Three switches provide a choice of heat settings. The appliance
is in standby mode when the mains lead is plugged in. This is
indicated by the red neon behind the flame effect screen. The
two selector switches are in the ON position when the side with
the markings on (i.e. I, or II) are pushed in.
Push button switch 1
Selector switch 2 (I)
Selector switch 3 (II)
Thermostat (T) - see Fig. 2
In order to maintain a certain room temperature, set the controller
to 'max.'. Operate the appliance at full power until the required
room temperature is reached. Set back the thermostatic controller
until the appliance switches off with an audible 'click'. This
temperature will be kept almost constant by the thermostatic
control switching on and off automatically. Please note that the
appliance can only be switched on when the thermostat setting
is higher then the room temperature.
Remote control - see Fig. 3
The maximum range of use is ~ 15metres.
Warning: It takes time for the receiver to respond to the
transmitter.
Do not press the buttons more than once within two seconds
for correct operation.
Battery information - see Fig. 5
1. To activate the remote control remove the battery isolation
strip, which is used to ensure your remote control reaches you
fully charged.
2. To replace the remote control battery, turn over the remote
control, and follow the diagram embossed on the remote control
3. Only use CR2025 or CR2032 size of batteries.
Controls the electricity supply to the
heater and flame effect. Press for
'ON' and 'Standby'. If both selector
switches 2 and 3 are in the OFF
position, the product works on flame
effect only.
Provides 1kW heat output.
Provides 2kW output with switch 2.
Discard leaky batteries
Dispose of batteries in the proper manner according to provincial
and local regulations.
Any battery may leak electrolyte if mixed with a different battery
type, if inserted incorrectly, if all the batteries are not replaced at
the same time, if disposed of in a fire, or if an attempt is made
to charge a battery not intended to be recharged.
Thermal Safety Cut-out
A thermal safety cut-out is incorporated in the heater to prevent
damage due to overheating. This can happen if the heat outlet
was restricted in any way. The heater will switch on once the
obstruction has been removed and the heater has cooled. If the
cut-out continues to operate intermittently, the heater should be
switched off and a service agent contacted.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.
Light Emitting Diode
This fire is fitted with LED (Light Emitting Diode) lamps. These
LED lamps are maintenance-free and should not require
replacing during the life of the product.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive
cleaners. The glass viewing screen should be cleaned carefully
with a soft cloth. DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or fluff the soft brush
attachment of a vacuum cleaner should occasionally be used
to clean the outlet grille of the fan heater.
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not
be disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice
in your country.
After Sales Service
Should you require after sales service or should you need to
purchase any spares, please contact the retailer from whom
the appliance was purchased or contact the service number
relevant to your country on the warranty card.
Please do not return a faulty product to us in the first instance
as this may result in loss or damage and delay in providing
you with a satisfactory service. Please retain your receipt as
proof of purchase.