VONROC WS501AC Traducción Del Manual Original página 5

f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust related hazards.
h) Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach of child­
ren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in
the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
WWW.VONROC.COM
5) Service
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
ADDITIONAL SAFETY WALL PAPER STEAMER
• Ensure boiler is placed on a flat level surface
and should the boiler become tilted in use level
again immediately. Failure to do so can result
in severe overheating, complete element failure
and void of your guarantee.
• Block boiler unit securely if using on stairs
• The boiler becomes hot in use, move only by
using the carrying handle.
• Steam is produced at 100°C be careful, wear
protective clothing and protect your hands with
heat resistant gloves or mitts.
• Never point hose or steam plate at anyone.
• Always keep steam plate tilted away from face
and body, beware of hot drips and regularly
empty collected condensation from plate –
especially when stripping ceilings and high areas.
• Never remove elbow filler cap or detach hose
whilst unit is operating.
• Never block the safety valves on the top of the
boiler.
• Do not overfill the reservoir.
• Allow to cool completely before emptying boiler.
• Do not stan on boiler of hose.
• So not drag or try to move the boiler by pulling
the mains lead.
• Do not allow water or steam to enter light swit-
ches or power points.
• Do not leave unattended.
• Use only standard tap water, never add deter-
gents of chemicals.
• Extreme care must be taken if the unit is used in
bathrooms. Always be aware of danger of elec-
trocution from stored water in baths and sinks.
• It is recommended that a RCD (residual current
device) Rated at 30mA is fitted into the mains
supply socket for added protection against
electric shock.
• The appliance must be unplugged after use
and before cleaning of user maintenance of the
appliance.
• Do not remove the filler cap while the unit is
operating. Switch off and allow the appliance to
cool for 2 minutes before removing the cap to
refill boiler.
EN
5