Manuales relacionados para Truper SINCO-12X
Resumen de contenidos para Truper SINCO-12X
- Página 1 Manual Slide compound miter saw Applies for: Code Model 12464 SINCO-12X SINCO-12X Read the user’s manual thoroughly CAUTION before operating this tool.
- Página 2 Unpacking and Assembly Keep this manual for future references. Assembly The illustrations in this manual are for reference Tightening Up only. They might be different from the real tool. Operation Troubleshooting Maintenance Notes Authorized Service Centers Warranty Policy SINCO-12X ENGLISH...
- Página 3 Technical Data SINCO-12X Code 12464 Description Slide compound miter saw Discs 12” with 60 teeth and 12” with 100 teeth Shaft diameter 1” Voltage Frequency 127 V 60 Hz Current 16 A Power Speed 4 500 RPM Duty cycle 50 minutes work and 20 minutes idle. Maximum 6 hours per day.
- Página 4 General power tool safety warnings WARNING! Read carefully all safety warnings and instruction listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references.
- Página 5 Safety warnings for stationary saws • Before setting new cutting discs make sure they are not General banged or damaged. If necessary, replace immediately. • Do not use the saw to cut metal, masonry or concrete. • When working with the saw stand aside the disc, never in •...
- Página 6 Parts 1. Cutter head. 2. Cutter head lock knob. 3. Handle. 4. Switch. 5. Carrying handle. 6. Disc upper guard. 7. Retractable guard. 8. Guard retracting arm. 9. 12” Tungsten carbide cutting disc with 60 teeth. 10. Shaft lock. 11. Motor. 12.
- Página 7 Parts Unpacking and assembly Due to tight quality controls there is a small probability that the tool has defects or missing parts. If there is any problem, before using the tool and to prevent severe injury, please go to a Authorized Service Center •...
- Página 8 Assembly Side extension arms • The arms are useful to support work pieces exceeding the cutting table area. • To install onto the worktable loosen the extension arms locks (22). • Set the extension arms on both sides of the table. Tighten the locks.
- Página 9 Assembly Cutting disc replacement CAUTION • Wear protective gloves to prevent • Remove the cutting disc. injuries when changing or setting the cutting disc. • Apply a drop of lubricant in the inside and outside • Disconnect the tool from the power source. washers onto the side where they make contact with the •...
- Página 10 Tightening Up Tighten up the rotating table to make miter cuts • To make 45° and up to -45° miter cuts use the rotating table (15). • Loosen the control knob (17) to release the rotating table. • Turn the table into the desired angle. Use the miter scale (18) as an aid.
- Página 11 Tightening Up Tighten up the angle to make bevel cuts • Disconnect the tool. • Lower and secure the cutter head (see page 7). • Adjust the rotating table to make 0° miter cuts, and keep the cutter head column at 0° (see page 10). •...
- Página 12 Operation Start up • To start the saw, tighten and keep the switch pressed (4). • To stop the saw, release the switch. When making this movement the automatic brake activates and stops the saw in seconds. • To prevent non-qualified persons using CAUTION the tool, there is an orifice for inserting a padlock in the switch and hinder its use.
- Página 13 Troubleshooting Problem Cause Solution The saw will not start. • The power cord is disconnected from the • Connect the power cord. power source. • Replace fuse or activate the circuit breaker. • Power fault: blown fuse or flipped circuit breaker. •...
- Página 14 Notes ENGLISH...
- Página 15 Authorized Service Centers In the event of any problem contacting a Truper Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 018-7873 to get information about the nearest Service Center.
- Página 16 . Transportation costs resulting from compliance of this warranty will be covered by For questions or comments, call 800-690-6990. Made in China. Imported by Truper S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257 Stamp of the business.