Publicidad
Idiomas disponibles
Idiomas disponibles
H-1619
SEMI-AUTOMATIC
STRETCH WRAP
MACHINE WITH SCALE
WARNING! Make sure that only qualified
personnel perform inspection, troubleshooting
and part replacement.
CAUSES
OPERATING ISSUE
Machine not
Main power is turned off.
powering on.
Machine not plugged into 120VAC
outlet.
Power supply faulty.
Internal battery not charged.
Film carriage foot engaged.
Film carriage
FILM CARRIAGE SPEED dial not set high
malfunctioning.
enough.
Resistance of potentiometer not equal
to 5K_ across.
The carriage limit switch lever arm is
obstructed.
Microcontroller card inside electrical
enclosure not turned on.
PAGE 1 OF 6
1-800-295-5510
uline.com
TROUBLESHOOTING
RECOMMENDATIONS
Check that power is going to the scale. Verify that
switch is turned on.
Verify the voltage going to the scale matches
the power supply labels on the power module or
scale.
Remove obstruction from Film Carriage foot.
Adjust potentiometer towards 100% to set speed.
Tighten wiring, replace dial if necessary.
Remove obstruction and/or clean limit switch
head.
Check and switch on the main circuit breaker.
Para Español, vea páginas 3-4.
Pour le français, consulter les pages 5-6.
CAUTION! Disconnect all power, including
external control power that may be present,
before servicing the frequency drive
controllers. WAIT for three (3) minutes for
the DC bus capacitors to discharge. The
frequency drive controller's display and/or LEDs
are not accurate indicators of the absence of
DC bus voltage.
0322 TH-1619
Publicidad
Tabla de contenido
Solución de problemas
Manuales relacionados para Uline H -1619
Resumen de contenidos para Uline H -1619
- Página 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-1619 1-800-295-5510 uline.com SEMI-AUTOMATIC STRETCH WRAP MACHINE WITH SCALE TROUBLESHOOTING WARNING! Make sure that only qualified CAUTION! Disconnect all power, including personnel perform inspection, troubleshooting external control power that may be present, and part replacement.
- Página 2 Check and switch on main circuit breaker. enclosure not turned on. The turntable motor is not running. Tighten or replace motor wiring as necessary. Check turntable for mechanical restrictions. Replace microcontroller or turntable output relay. 1-800-295-5510 uline.com PAGE 2 OF 6 0322 TH-1619...
-
Página 3: Solución De Problemas
H-1619 800-295-5510 uline.mx DESPACHADORA SEMIAUTOMÁTICA DE PELÍCULA ELÁSTICA CON BÁSCULA SOLUCIÓN DE PROBLEMAS ¡ADVERTENCIA! Asegúrese de que sólo ¡PRECAUCIÓN! Desconecte toda la corriente, incluyendo el control externo de corriente personal calificado lleve a cabo la que pudiera estar presente, antes de dar inspección, solución de problemas y... -
Página 4: Continuación De Solución De Problemas
El motor de la plataforma giratoria no está Ajuste o reemplace el cableado corriendo. del motor como se requiera. Revise la plataforma giratoria de limitaciones mecánicas. Reemplace el microcontrolador o el interruptor de salida de la plataforma giratoria. 800-295-5510 uline.mx PAGE 4 OF 6 0322 TH-1619... -
Página 5: Problème De Fonctionnement
H-1619 1-800-295-5510 uline.com DISTRIBUTEUR DE FILM ÉTIRABLE SEMI-AUTOMATIQUE AVEC BALANCE DÉPANNAGE AVERTISSEMENT! Veillez à ce que seul un MISE EN GARDE! Coupez toutes les alimentations, ARRÊT personnel qualifié effectue les inspections, le dont celle de la commande externe qui peut être présente, avant toute opération d'entretien des... -
Página 6: Dépannage Suite
Serrez ou remplacez le câblage du moteur au ne fonctionne pas. besoin. Vérifiez les contraintes mécaniques de la plaque tournante. Remplacez le microcontrôleur ou le relais de sortie de la plaque tournante. 1-800-295-5510 uline.com PAGE 6 OF 6 0322 TH-1619...