Publicidad
Idiomas disponibles
Idiomas disponibles
Do not put the power tool down before the
u
router bit has come to a complete stop. Ap-
plication tools that are still running can cause
injuries.
Edge or profile routing (see figure H)
For edge and profile routing without a parallel
guide, the router bit must be fitted with a pilot pin
or a ball bearing.
While it is switched on, guide the power tool to-
wards the workpiece from the side until the pilot
pin or the ball bearing of the router bit is touching
the side of the workpiece edge that you want to
machine.
Guide the power tool along the workpiece edge.
Pay attention that the router is positioned perpen-
dicularly. Too much pressure can damage the
edge of the workpiece.
The following maximum workpiece dimensions
apply for edge and profile milling operations:
Material
Hardwood
Softwood
Plastic
MDF sheets
Plywood sheets
Temperature monitoring/overload protection
indicator
English
The red LED indicator (3) helps you to protect the
battery against overheating and the motor against
overload.
If the LED indicator (3) is lit up permanently in
red, the temperature of the battery is too high and
the power tool switches off automatically.
– Switch the power tool off.
– Allow the battery to cool down before you carry
on working.
If the LED indicator (3) is flashing red, then the
power tool is blocked and will switch off automat-
ically.
Pull the power tool out of the workpiece.
The power tool will continue to work as soon as
the blockage is rectified.
Recommendations for Optimal Handling of the
Battery
English
Protect the battery against moisture and water.
Only store the battery within a temperature range
of −20 to 50 °C. Do not leave the battery in your
car in the summer, for example.
Occasionally clean the ventilation slots on the bat-
tery using a soft brush that is clean and dry.
A significantly reduced operating time after char-
ging indicates that the battery has deteriorated
and must be replaced.
Follow the instructions on correct disposal.
18 | English
Maintenance and Service
Maintenance and Cleaning
Remove the battery from the power tool be-
English
u
fore carrying out work on the power tool (e.g.
maintenance, changing tool, etc.). The bat-
tery should also be removed for transport and
storage. There is risk of injury from unintention-
ally pressing the on/off switch.
To ensure safe and efficient operation, al-
u
ways keep the power tool and the ventilation
slots clean.
Clean the power tool with a vacuum cleaner, paint
brush or hand brush after use. Ensure that the
guide columns are free of wood dust. Apply a
drop of lubricant to the smooth guide column (19)
(see figure I).
Radius
Chamfer
Transport
mm
mm
10
6
The recommended lithium-ion batteries are sub-
ject to legislation on the transport of dangerous
12
10
goods. The user can transport the batteries by
12
10
road without further requirements.
12
10
When shipping by third parties (e.g.: by air trans-
10
6
port or forwarding agency), special requirements
on packaging and labelling must be observed. For
preparation of the item being shipped, consulting
an expert for hazardous material is required.
Dispatch battery packs only when the housing is
undamaged. Tape or mask off open contacts and
pack up the battery in such a manner that it can-
not move around in the packaging. Please also
observe the possibility of more detailed national
regulations.
Disposal
Only for EU countries:
According to the Directive 2012/19/EU, power
tools that are no longer usable, and according to
the Directive 2006/66/EC, defective or used bat-
tery packs/batteries, must be collected separately
and disposed of in an environmentally correct
manner.
English
English
English
Power tools, rechargeable batteries,
accessories and packaging should be
sorted for environmental-friendly recyc-
ling.
Do not dispose of power tools and bat-
teries/rechargeable batteries into
household waste!
English
1 609 92A 72D • 22.12.21
English
Publicidad
