Publicidad
Idiomas disponibles
Idiomas disponibles
Date Code Position (Fig. B)
The date code
12
, which also includes the year of manufacture,
is printed into the housing.
Example:
2021 XX XX
Year and Week of Manufacture
Description (Fig. A)
WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Extendable hooks
1
Power button
2
Light selector button
3
Tab
4
5
Reciever
Lens
6
Battery
7
Release button
8
Intended Use
Your cordless LED under‑bonnet light has been designed for
professional lighting applications.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
This under‑bonnet light is a professional tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
•
Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
•
This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
WARNING: Use only D
Installing and Removing the Battery Pack
(Fig. B)
CAUTION: DO NOT USE THIS UNDER‑BONNET LIGHT
WITH A BATTERY GREATER THAN 12 AH CAPACITY.
nOTE: For best results, make sure your battery pack is
fully charged.
WALT battery packs and chargers.
e
1. To install the battery pack
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the release
button
8
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D
WALT battery packs include a fuel gauge which consists
e
of three green LED lights that indicate the level of charge
remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button
10
. A combination of the three green LED lights will
illuminate designating the level of charge left. When the level of
charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Power ON/OFF Button (Fig. A)
1. To turn the light on, press the power button
setting is high mode.
2. Press the button again and the light will convert to low mode.
3. Press again to turn the light off.
Low Battery Indicator (Fig. A)
As the battery
7
nears a fully discharged state, the light will
blink twice and then dim, dropping the brightness of the light
below the normal level. The light will continue to blink twice
every 45 seconds until the battery is fully discharged at which
time the light will turn off. Indication time will vary based on
battery pack capacity.
Light Selector Button (Fig. A)
The under‑bonnet light can operate using one or both LED lenses.
1. With the light on, press the light selector button
between left, right or both LED lenses.
EngLIsh
7
into the tool handle, align the
2
, this initial
3
to cycle
23
Publicidad
