Bosch GWS 2000 J Professional Manual Original página 19

(7) Locking screw for protective guard
(8) Mounting flange with O‑ring
a)
(9) Grinding disc
(10) Clamping nut
(11) Two-pin spanner for clamping nut
(12) Quick-clamping nut
a)
(13) Carbide grinding head
(14) Protective guard for cutting
a)
(15) Cutting disc
a)
(16) Hand guard
Technical data
Angle Grinder GWS 2000 J
Article number 3 601 HF2 0.. 3 601 HF2 1.. 3 601 HF4 0.. 3 601 HF4 1.. 3 601 HF4 2.. 3 601 HF4 3..
Rated power input W
−1
Rated speed min
Max. grinding disc mm
diameter
Grinding spindle
thread
Max. thread length mm
of grinding spindle
Restart protection
Soft start
Weight according to EPTA-Procedure 01:2014
– with low-vibra- kg
tion auxiliary
handle
– with standard kg
auxiliary handle
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Notes on mains connection requirements for GWS 2000 P/GWS 2200 P/GWS 2400 P:
The appliance meets IEC 61000-3-11 requirements and is subject to conditional connection. The appliance can lead to occa-
sional voltage fluctuations under unfavorable power conditions. The impedance of this appliance is set as Z
user must make sure, that the connection point, with the impedance Z
impedance requirement: Z ≥ Z
actual
thority.
Noise/Vibration Information
Noise emission values determined according to
EN 60745‑2‑3.
Typically the A-weighted noise level of the power tool are: 97
dB(A); sound power level 108 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745‑2‑3:
Surface grinding (roughing):
2 2
a = 7.5 m/s , K = 1.5 m/s ,
h
Bosch Power Tools
(17) Spacer discs
(18) Rubber sanding pad
(19) Abrasive disc
(20) Round nut
(21) Cup brush
a)
(22) Diamond cutting disc
(23) Extraction guard for cutting with cutting guides
a)
a) Accessories shown or described are not included with the
GWS 2000 P GWS 2200 J
2000 2000
6500 6500
230 230
M14 M14
25 25
● –
● –
5.2 5.1
5.1 5.0
/II /II
. If Z is unknown, determine Z
max max
Disc sanding:
a
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
a)
a)
a)
a)
a)
a)
product as standard. You can find the complete selection of
accessories in our accessories range.
GWS 2200 P GWS 2400 J
2200 2200
6500 6500
230 230
M14 M14
25 25
● –
● –
5.5 5.4
5.4 5.3
/II /II
, on which the appliance shall be plugged in meets the
max
in consultation with the network supplier or supply au-
max
2 2
= 4.5 m/s , K = 1.5 m/s .
h
English | 19
a)
GWS 2400 P
2400 2400
6500 6500
230 230
M14 M14
25 25
● –
● –
5.5 5.4
5.4 5.3
/II /II
= 0.18 Ω. The
actual
1 609 92A 824 | (30.09.2022)