Bosch GWS 2000 J Professional Manual Original página 20

20 | English
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
Fitting
Fitting Protective Equipment
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Applica-
tion Service" section for addresses.
Protective guard for grinding
Place the protective guard (6) on the spindle collar. Adjust
the position of the protective guard (6) to the requirements
of the operation and lock the protective guard (6) with the
locking screw (7).
Adjust the protective guard (6) such that sparking in
u
the direction of the operator is prevented.
Protective guard for cutting
Always use the protective guard for cutting (14) when
u
cutting with bonded abrasives.
Provide sufficient dust extraction when cutting stone.
u
The protective guard for cutting (14) is fitted in the same
way as the protective guard for grinding (6).
Extraction guard for cutting with a guide block
Observe the operating instructions of the extraction guard
when fitting the extraction guard for cutting with a cutting
guide (23).
Side handle
Do not operate your power tool without the side
u
handle (3).
Screw the side handle (3) on the left or right of the machine
head depending on how your are working.
Hand guard
Always fit the hand guard (16) when working with the
u
rubber sanding plate (18) or with the cup brush/disc
brush/flap disc.
Attach the hand guard (16) to the side handle (3).
Fitting the Abrasive Tools
Pull the plug out of the socket before carrying out any
u
work on the power tool.
1 609 92A 824 | (30.09.2022)
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Clean the grinding spindle (5) and all the parts to be fitted.
Lock the grinding spindle with the spindle lock button (1)
before clamping and releasing the abrasive tools.
Do not press the spindle lock button while the grind-
u
ing spindle is moving. The power tool may become dam-
aged if you do this.
Grinding/cutting disc
Pay attention to the dimensions of the abrasive tools. The
diameter of the hole must match that of the mounting flange.
Do not use an adapter or reducer.
When using diamond cutting discs, ensure that the arrow in-
dicating the direction of rotation on the diamond cutting disc
matches the direction of rotation of the power tool (see the
direction of rotation arrow on the machine head).
See the graphics page for assembly instructions.
To fasten the grinding/cutting disc, screw on the clamping
nut (10) and tighten with the two-hole spanner. (see " Quick-
clamping nut ", page 21).
After fitting the abrasive tool, check that the abrasive
u
tool is fitted correctly and can turn freely before
switching on the power tool. Make sure that the abras-
ive tool does not brush against the protective guard or
other parts.
A plastic part (O-ring) is fitted around the cent-
ring collar in the mounting flange (8). If the O-
ring is missing or damaged, the mounting
flange (8) must be replaced before operation
can resume.
Flap disc
Always fit the hand guard (16) when working with the
u
flap disc.
Rubber sanding pad
Always fit the hand guard (16) when working with the
u
rubber sanding pad (18).
See the graphics page for fitting instructions.
Before fitting the rubber sanding pad (18), place the two
spacer discs (17) on the grinding spindle (5).
Screw on the round nut (20) and tighten with the two-pin
spanner.
Cup brush/disc brush
Always fit the hand guard (16) when working with the
u
cup brush or disc brush.
See the graphics page for fitting instructions.
The cup brush/disc brush must be screwed onto the grinding
spindle until it rests firmly against the grinding spindle flange
at the end of the grinding spindle thread. Tighten the cup
brush/disc brush with an open-ended spanner.
Bosch Power Tools