Peach PL120 Instrucciones De Servicio página 5

UK
IMPORTANT SAFETY INSTRUCTIONS -
KEEP FOR FUTURE USE
The machine is for indoor use only. Plug the machine into
an easily accessible outlet.
To avoid electric shocks, the laminator must not be
used in humid or wet conditions and water must never
be allowed to come into contact with the machine, the
connection cable or the socket.
●
Ensure the machine is on a stable surface.
●
Keep the machine away from heat and water sources.
●
Turn off the machine after each use.
●
Unplug the machine when not in use for extended
periods of time.
●
Keep away from pets, while in use.
●
The power cord must not come into contact with hot
surfaces.
●
Don't leave power cord hanging from cupboards or
shelves.
●
The device must not be used if the power cord is
damaged.
●
Don't attempt to open or otherwise repair the machine.
●
Don't exceed the machines quoted performance.
●
Don't allow children to use this machine.
●
Don't laminate sharp or metal objects (eg: staples,
paper clips).
●
The laminator is not intended for commercial or
industrial applications.
●
After 2 hours of operation the appliance must be
allowed to cool down for at least half an hour (Switch
off).
Description
❶ Power switch (ON/OFF)
❷ Power indicator light (blue)
❸ Mode indicator lights (green)
❹ Selector button
❺ Slot for pouch input (Rear)
❻ Pouch ejector slot (Front)
❼ Anti-Blocking switch (ABS)
❽ Pouch tray
❾ Pouch positioning aid
Laminating
Only use special films designed specifically for laminating.
Test laminate scrap sheets and set the machine before
final laminating. Remove staples and other metal articles
prior to laminating.
Heat-sensitive documents (eg: tickets, ultrasounds etc)
cannot be laminated on hot settings. Don't laminate an
empty pouch.
Instruction Manual PL120
1. Turn the machine on by setting the power switch ❶ to
the "I" position. The blue power indicator light ❷ and the
green mode indicator light (cold) ❸ are lighting up.
2. If the machine is not in use, set the power switch ❶ to
the "0" position and the power indicator (blue light) ❷ is
off.
3. Use the selector button ❹ to select the desired pouch
type.
COLD laminating:
The green indicator light ❸ for COLD laminating lights up
as soon as the power switch ❶ is set to the "I" position.
The machine is ready for cold laminating.
Hint: For cold laminating special laminating pouches
have to be used, which are not part of the included
starter pack.
HOT laminating:
80mic pouches: Press the selector button ❹ and select
"80mic", and the "80mic" indicator light ❸ starts to
flash green. At this time, the machine enters the warm-
up cycle. As soon as the indicator light ❸ "80mic"
glows permanently the machine is ready and laminating
of 80mic pouches can begin.
125mic pouches: Press the selector button ❹ and
select "125mic", and the "125mic" indicator light ❸
starts to flash green. At this time, the machine enters the
warm-up cycle. As soon as the indicator light "125mic"
❸ glows permanently the machine is ready and
laminating of 125mic pouches can begin.
Note:
To switch from 125mic to 80mic or to COLD laminating
press the selector button ❹ to choose the desired
laminating method. The desired mode indicator ❸ will
start to flash. It will take several minutes to cool down
the device. Laminating of the desired pouch type may
only start if the respective indicator light ❸ glows
permanently. Otherwise the laminated document could
be damaged which may also lead to damage to the
machine itself.
4. Lay the document to be laminated into a laminating
pouch of the appropriate size. Make sure that all corners
of the document have at least two millimeters of space
from the edge of the laminating pouch.
5. Now lay the laminating pouch, sealed side first on the
pouch tray ❽ . Adapt the pouch positioning aid ❾ to
the pouch size used and push the pouch slowly into the
pouch input slot ❺ . Guide the pouch into the laminator
until it is gripped and pulled in by the rollers