Publicidad
Idiomas disponibles
Idiomas disponibles
INSTALLING & REMOVING UV-C BULB
CHANGE BULB INDICATOR
The white light above the UV indicator will begin to flash continuously when it is time to replace
the UV-C bulb. Replace the bulb according to the directions then press the UV control button and
hold for 3 seconds to restart the system.
1. The UV-C bulb is in a compartment above the filter in the purifier.
2. To access, first follow the instructions to remove the filter.
3. Turn the purifier on its side for easier access to the compartment.
4. Reach inside to detach the UV-C grate. Use a Philips head screwdriver to remove the
four (4) screws. Detach the grate.
5. The UV-C Bulb is removed by carefully grasping the bulb with a clean cloth or tissue,
twisting it 90 degrees and pulling the bulb straight out of the unit.
6. The UV-C Bulb is reinstalled by sliding it, horizontally, back into the slots at the top of the unit.
Twist 90 degrees to lock into place.
7. Press and hold the UV Control Button for 3 seconds to reset UV Bulb Change Indicator.
IMPORTANT: The UV-C bulb should be replaced every 10 months depending on use.
IMPORTANT: If the filter is not placed in properly or the filter cover is not secure, the
unit will not turn on.
CLEANING & MAINTENANCE
CLEANING
• Always unplug the appliance before you clean it.
• Never immerse the appliance in water or any other liquid.
• Never use aggressive or flammable cleaning agents such as bleach or alcohol to clean any
part of the appliance.
BODY OF THE APPLIANCE
Regularly clean the inside and outside of the body to prevent dust from collecting.
1. Wipe away dust with a soft dry cloth from the body of the appliance.
2. Clean the air inlet and the air outlet with a soft dry cloth.
PRE-FILTER SCREEN
The pre-filter/charcoal layer collects larger dust and debris and should be cleaned monthly or
more frequently depending on use. Remove and clean regularly with the brush attachment of
your vacuum cleaner. This will remove the lint and dirt and help maintain the life of the filter.
(See filter replacement to locate and clean or remove the filter).
E-8
REPLACEMENT PARTS
K
FILTER:
Model No.
FLT9400
IMPORTANT: To maintain performance of the air cleaner, use
Guardian Technologies GENUINE Replacement Parts only.
To purchase visit our website www.guardiantechnologies.com.
Note: Do NOT stick any foreign objects or your fingers inside the unit.
What is CADR?
CADR stands for "Clean Air Delivery Rate," which indicates the volume of filtered air delivered by
an air purifier. CADR ratings show the effectiveness of how efficient the air purifier is at capturing
fine particles from things like tobacco smoke and plant pollens from the room.
Clean Air Delivery Rate
From air cleaner to air cleaner, compare the CADR numbers. First look at suggested room size.
Then refer to the Clean Air Delivery Rate (CADR) numbers. The higher the number, the faster
the unit filters the air.
Refer to website for individual model CADR numbers.
TROUBLESHOOTING GUIDE
PROBLEM
SOLUTION
Unit shuts off unexpectedly
Check that the unit is plugged into a working electrical outlet.
or does not operate.
Check to see if the motor protector is triggered.
Check that the filter and back panel are installed correctly.
Unplug/replug into the outlet.
Call customer service.
No air circulating from the unit. Unplug unit. Check filter. Clean or replace filter if necessary.
Odors not removed.
Make sure the filter is clean. Replace if necessary.
Discharged air has an odor.
Check to see if the filter is heavily soiled. Replace if necessary.
Increase in noise level.
Make sure the filter is clean. Replace if necessary.
Filter indicator light on display
Replace filter and reset light.
is illuminated.
UV-C indicator light is flashing. Replace bulb and reset light.
Air quality status remains poor. Check to see if the filter is heavily soiled. Replace if necessary.
Increase the fan speed to circulate air.
Check out our
Filter Replacement Program
™
UV BULB:
www.guardiantechnologies.com
Model No.
LB9000
E-9
Publicidad
