Makita DUB187 Manual De Instrucciones página 9

14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool imme-
diately after use as it may get hot enough to
cause burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge. It may cause heating, catching fire,
burst and malfunction of the tool or battery car-
tridge, resulting in burns or personal injury.
17. Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near high-voltage electri-
cal power lines. It may result in a malfunction or
breakdown of the tool or battery cartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita battery
cartridges. Use of non-genuine Makita battery car-
tridges, or battery cartridges that have been altered,
may result in the battery bursting causing fires, per-
sonal injury and damage. It will also void the Makita
warranty for the Makita tool and charger.
Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4. When not using the battery cartridge, remove
it from the tool or the charger.
5. Charge the battery cartridge if you do not use
it for a long period (more than six months).
ASSEMBLY
CAUTION:
Always be sure that the machine is
switched off and the battery cartridge is removed
before carrying out any work on the machine.
Installing or removing the wheels
To install the wheels, insert the claw of the wheels into
the slot of the nozzle as shown in the figure.
► Fig.1: 1. Claw 2. Slot
To remove the wheels, slide the claw upward slightly,
and then remove the wheels.
► Fig.2: 1. Claw
Installing the nozzle
Loosen and remove the screw of the main unit. Align the
protrusions on the nozzle with the grooves on the main
unit, then insert the nozzle into the main unit until the
protrusions snap into place. Tighten the screw securely
to fix the nozzle.
► Fig.3: 1. Screw 2. Nozzle 3. Protrusion
Installing or removing the dust bag
Hook the claw of the dust bag to the hook of the main
unit, then hook the front side of the handle of the dust
bag to the main unit, and then pull up the rear side of
the handle until handle snaps into place as shown in
the figure.
► Fig.4: 1. Claw 2. Handle 3. Dust bag
To remove the dust bag, perform the installation proce-
dure in reverse.
Installing or removing the wide
nozzle
Optional accessory
Insert the wide nozzle with its protrusions facing up into
the nozzle.
► Fig.5: 1. Protrusion
Attaching the shoulder strap
CAUTION:
When you use the machine in com-
bination of the backpack-type power supply such
as portable power pack, do not use the shoulder
harness included in the machine package, but use
the hanging band recommended by Makita.
If you put on the shoulder harness included in the
machine package and the shoulder harness of the
backpack-type power supply at the same time,
removing the machine or backpack-type power supply
is difficult in case of an emergency, and it may cause
an accident or injury. For the recommended hanging
band, ask Makita Authorized Service Centers.
CAUTION:
Be sure to attach the hooks of
the shoulder strap to the machine securely. If the
hooks are attached incompletely, they may come off
and cause an injury.
CAUTION:
Be sure to use the shoulder strap
dedicated to this machine. Using other shoulder
strap may cause an injury.
Attach the hook of the shoulder strap to the machine as
shown in the figure.
► Fig.6: 1. Hook
9 ENGLISH