Publicidad
Idiomas disponibles
Idiomas disponibles
• Regularly change the old oil to reduce releasing of dioxins
which are carcinogenic.
Intended use
• This appliance is intended to be used for commercial applica-
tions, for example in kitchens of restaurants, canteens, hos-
pital and in commercial enterprises such as bakeries, butch-
eries, etc., but not for continuous mass production of food.
• The appliance is designed for frying appropriate food only
such as French fries, etc. Any other use may lead to damage
to the appliance or personal injury.
• Operating the appliance for any other purpose shall be
deemed as a misuse of the device. The user shall be solely
liable for improper use of the device.
Grounding installation
This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk
of electric shock by providing an escape wire for the electric
current.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Control panel
(Fig.1 on page 3)
1. ON/OFF: Switch ON / Switch OFF
2. TIMER: Time setting up to 15 minutes
3. UP: Increase Time / Temperature
4. DOWN: Decrease Time / Temperature
5. FILL OIL: Fill oil alert indicator
6. Digital display: Show the Time / Temperature
7. HEATING: Heating indicator
8. KEEP WARM: Keep warm indicator
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See == >
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Operating instructions
• Make sure the tap is closed and that the oil tank has enough
oil, level should be between MIN and MAX marking.
• Connect the power plug to a suitable electrical supply outlet.
• Next, press the power switch at the rear side of the appliance
to connect the power supply. Green indicator on the power-
switch will light up.
• Now the appliance is connected to electrical supply.
• Press ON / OFF (1) to switch ON the appliance. FILL OIL (5)
indicator flashes and buzzer sound will be heard to alert the
user to fill up the oil tank container.
• Then, please make sure again the oil level is between the MIN
and MAX marking.
• If the oil tank contains enough oil, press FILL OIL (5) to can-
cel the buzzer sound and the indicator light. The display will
show the default temperature of 140°C.
• After that, press UP (3) or DOWN (4) button to increase or
decrease the temperature. (Range: 60°C ~ 190°C, with 5°C
interval).
• When the oil doesn't reach the set temperature, "HEATING
Indicator" will light up and "KEEP WARM Indicator" will go
out.
• When the oil temperature reaches the set temperature,
"HEATING Indicator" will go out and the "KEEP WARN Indi-
cator" will light up.
NOTE! During operation, if no temperature is set, the appliance
will maintain to the default temperature 140°C.
Setting Timer
• Timer can be set by pressing the TIMER (2) to enter TIMER
mode.
• Then, press UP (3) or DOWN (4) to increase or decrease the
time. (Range: 0 min ~ 15 mins, with 30 seconds interval). De-
fault setting is 0 min.
• When the timer is set, it will be stored automatically within
5 seconds. Then, timer will be started to count down from
the set time.
• Display (6) will alternate between Time remaining / Set tem-
perature.
• When the set time has elapsed, a beeping sound (long and
short) will be heard and "End" will be shown in the display
(6). The appliance will keep on heating if the set temperature
isn't reached.
• Press and hold the UP (3) or DOWN (4) for fast adjustment
of timer.
NOTE:
1. Press and hold the increase setting button (3) or decrease
setting button (4) for fast adjustment.
2. Every time, you press any button on the panel, a short beep
sound will be heard to alert the user.
3. After an extended period of operation, it is normal for the
cooling fan inside to continue running in OFF mode for
some time. Before unplug the appliance, wait until the
cooling fan stops running.
4. The appliance's outer surface is still hot even after switch
to OFF mode. Please wait the appliance completely cool
down before touching or cleaning.
5. If no any button on the control panel is pressed during op-
eration for 4 hours, the appliance will then switch to OFF
mode automatically.
RESET the safety cut-out (Hi-limiter or thermal
cut-out)
Please note that the RESET button is equipped with a protec-
tive cap to avoid overheat.
• Disconnect the appliance from the power supply.
• Allow the appliance to completely cool down.
GB
7
Publicidad
